AVSPARE.COM
parts catalog

TIMER 3534716 - Caterpillar



3534716 TIMER Caterpillar parts 3516C TIMER
Rating:
27
Alternative (cross code) number:
CA3534716
353-4716
3534716
Caterpillar 3534716 TIMER
Weight: 0.09 pounds 0 kg.

Buy TIMER 3534716 Caterpillar genuine, new aftermarket tractor parts with delivery
POWER MODULE,

Compatible equipment models: 3534716:

POWER MODULE  3516C   Caterpillar
Number on catalog scheme: 61
 
  For full view, you need register

Information:

Parts of the Event Code
Event Code - "E" identifies the code as an event code. "XXX(X)" represents a numeric identifier for the event code. The fourth "(X)" assigns one of three levels to the active event code according to the severity of the abnormal system condition. Next is a code description. Refer to the following example:
E360(1) Low Oil Pressure
E360(2) Low Oil Pressure
E360(3) Low Oil PressureThe definition for the levels of severity for an event are defined below:Level 1 - Level 1 alerts the operator that an engine system requires attention. The operator should check that the involved system condition or the operator should perform maintenance on the involved system at the earliest possible time.Level 2 - Level 2 requires a change in the operation of the engine or the performance of a maintenance procedure. Failure to correct the problem that caused this warning may result in damaged the engine components.Level 3 - Level 3 requires an immediate safe shutdown of the engine in order to avoid damage to the engine or injury to personnel around the engine. The problem that caused the event must be corrected before engine operation can resume.Active Event Codes
An active event code represents a problem with engine operation. Correct the problem as soon as possible.Active event codes are listed in ascending numerical order. The code with the lowest number is listed first.Illustration 1 is an example of the operating range of a sensor.
Illustration 1 g01365757
Example of the typical operating range of a sensor
(1) This area represents the normal operating range of the engine parameter.
(2) In these areas, the engine is operating in an unsafe operating range of the monitored parameter. An event code will be generated for the monitored parameter. The sensor circuit does not have an electronic problem.
(3) In these areas, the signal from the sensor is outside of the operating range of the sensor. The sensor circuit has an electronic problem. A diagnostic code will be generated for the sensor circuit. Refer to Troubleshooting, "Diagnostic Trouble Codes" for additional information on diagnostic codes.Logged Event Codes
When the Electronic Control Module (ECM) generates an event code, the ECM logs the code in permanent memory. The ECM has an internal diagnostic clock. The ECM will record the following information when an event code is generated:
The hour of the first occurrence of the code
The hour of the last occurrence of the code
The number of occurrences of the codeLogged events are listed in chronological order. The most recent event code is listed first.This information can be helpful for troubleshooting intermittent problems. Logged codes can also be used to review the performance of the engine.Clearing Event Codes
A code is cleared from memory when one of the following conditions occur:
The code does not recur for 100 hours.
A new code is logged and there are already ten codes in memory. In this case, the oldest code is cleared.
The service technician manually clears the code.Always clear logged event codes after investigating and correcting the problem which generated the code.Troubleshooting
For the basic troubleshooting

Caterpillar parts catalog:

Caterpillar parts catalog
3516C Power Module KEN00001-UP
PM3516 Power Module NAM00001-UP


Parts timer Caterpillar catalog:

1791937 TIMER AS
3516C, C15, C18, C27, C32, PM3412, PM3508, PM3512, PM3516, PMG3516, XQC1200, XQC1600
1694498 TIMER
3406E, 3412C, 3456
1422528 TIMER
3508, 3508B, 3512, 3512B, 3516, 3516B, PM3508, PM3512, PM3516
9Y8020 TIMER
3208, 3306, 3408, 3412, 3516
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.