parts catalog

TIRE 3843508 - Caterpillar

3843508 TIRE Caterpillar parts 725, 730
Alternative (cross code) number:
Caterpillar 3843508 TIRE

Buy TIRE 3843508 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 3843508:

ARTICULATED TRUCK  725   730   Caterpillar
  For full view, you need register


Start By: a. remove vibration damper and crankshaft pulleyb. remove oil pan 1. Disconnect elbow (1) at the torque converter oil cooler. 2. Fasten tooling (A) to the cylinder block oil pan flange.3. Install a 50 ton screw jack (2) under the mid point of tooling (A). 4. Remove the bolts and nuts that hold support (3) to frame (4).5. Raise the front of the engine with tooling (A) until engine support (3) is clear of frame (4).6. Remove engine support (3) from the trunnion. 7. Remove trunnion (5) from the timing gear cover. 8. Inspect resilient mount (6) which is part of trunnion (5).9. Remove resilient mount (6) from the adapter if it is worn or damaged.Install Engine Front Support And Trunnion
1. Be sure the surface for resilient mount (2) on adapter (1) is clean and free of nicks or burrs.2. Put adapter (1) in a hydraulic press so the adapter will be evenly supported when resilient mount (2) is pressed into place.3. Place resilient mount (2) on adapter (1) so the vertical centers are aligned. Dimension (X) must be 105.92 mm (4.170 in.). Recheck this alignment because incorrect alignment will result in resilient mount damage.
Use tooling (A) to press only against steel ring (3) of the resilient mount. Do not press against any other part of the resilient mount because damage to the resilient mount will occur.
4. Place tool (A) on steel ring (3), and use a hydraulic press to install resilient mount (2) onto adapter (1). Install resilient mount (2) to dimension (Y). Dimension (Y) must be 25.4 mm to 27.4 mm (1.00 to 1.08 in.). 5. Install trunnion (4) to the timing gear cover.6. Install bracket (5). Use the two 4 1/2 in. long bolts to secure the bracket.7. Tighten the bolts for trunnion (4) and bracket (5) to a torque of 86 to 114 N m (65 to 85 lb.ft.). 8. Fasten support (6) to trunnion (4). Tighten the four bolts to a torque of 178 to 232 N m (130 to 170 lb.ft.).9. Use tool (B) to lower the front of the engine until support (6) contacts the frame. Install bolts (7), the nuts and washers. Tighten the bolts to a torque of 313 to 407 N m (230 to 300 lb.ft.).10. Remove tooling (A). 11. Be sure the mating surfaces of elbow (8) and the torque converter oil cooler are clean.12. Install a new O-ring seal in elbow (8), and fasten the elbow to the torque converter oil cooler.End By: a. install oil panb. install vibration damper and crankshaft pulley

Caterpillar parts catalog:

Caterpillar parts catalog
725 Articulated Truck B1L00001-UP (MACHINE) POWERED BY C11 Engine
730 Articulated Truck B1M00001-UP (MACHINE) POWERED BY C11 Engine
730 OEM Articulated Truck WWB00001-UP (MACHINE) POWERED BY C11 Engine
725 OEM Articulated Truck WWA00001-UP (MACHINE) POWERED BY C11 Engine

Parts tire Caterpillar catalog:

1635118 TIRE
725, 725C, 730, 730C, 735, D300E, D300E II, D350E, D350E II
2577483 TIRE
16H, 16H NA, 725, 725C, 730, 730C
3095035 TIRE
725, 725C, 730, 730C
3087767 TIRE
725, 725C, 730, 730C
2849052 TIRE
725, 725C, 730, 730C
3914372 TIRE
725, 725C, 730, 730C
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.