parts catalog

TOOL GP 5087868 - Caterpillar

5087868 TOOL GP Caterpillar parts TOOL
Alternative (cross code) number:
Caterpillar 5087868 TOOL GP
Weight: 313 pounds 142 kg.

Buy TOOL GP 5087868 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register


Illustration 1 g01074605
Schematic of the Loader Auxiliary Valve Port B SolenoidThis diagnostic code is associated with the Loader Auxiliary Valve Port B Solenoid. This diagnostic code is recorded when the ECM reads the signal from the solenoid and the ECM determines that the signal is erratic, intermittent, or incorrect.The possible causes of this diagnostic code are listed:
Wire (E544-GN) is shorted to the ground circuit while the machine is in operation.
Wire (E544-GN) is shorted to the +battery.
An open circuit exists.
The ECM has failed. This is unlikely.Note: Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure. System Response:
The system will not initialize after power is cycled.
The hydraulic functions for extend, retract, reverse and forward are lost after power is cycled.
There will be no effect to the systems after powerup until the next reset of the valve ECM.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 2243 FMI 02 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.Test Step 1. VERIFY SOFTWARE VERSIONNote: From SIS or the latest release of the CD for SIS, check and record the latest software version for the machine electronic controls.
Verify the machine ECM has the latest software version loaded.
Verify that the valve ECM's have the latest software loaded.Expected Result:All of the software is up to date.Results:
OK - All of the software is up to date. Proceed to Test Step 2.
NOT OK - There is a more recent software release available.Repair: Flash all controls with the latest software release. Refer to Testing and Adjusting, "Electronic Control Module (ECM) - Flash Program".STOPTest Step 2. CHECK THE HARNESS.
Turn the key start switch to the OFF position.
Inspect the harness.
Check for the proper mating.
Check the exposed wires for nicks and abrasions.
Check for moisture, dirt, or corrosion.
Check the pin/socket for a proper fit.
Disconnect the machine harness connectors from the machine ECM.
At the machine harness connector, measure the resistance from connector contact 1 (wire E544-GN) to J1-52 (wire E544-GN) of the machine ECM. Expected Result:The resistance should be less than 5 ohms.Results:
OK - The resistance is less than 5 ohms. The machine harness is correct. Proceed to test step 3.
NOT OK - The resistance is greater than 5 ohms. There is an open in the machine harness. The open is between the modules for the signal (wire E544-GN).Repair: Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Clean the contacts of the harness connectors.
Reconnect all harness connectors.
Observe the

Parts tool Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.