AVSPARE.COM
parts catalog

TOOTH GP 2332885 - Caterpillar



2332885 TOOTH GP Caterpillar parts 301.4C, 301.5, 301.7D, 301.7D CR, 302.2D, 302.4D, 302.5, 302.7D, 303.5D, 303.5E, 303E CR, 304D CR, 304E TOOTH
Rating:
62
Alternative (cross code) number:
CA2332885
233-2885
2332885
Caterpillar 2332885 TOOTH GP

Buy TOOTH GP 2332885 Caterpillar genuine, new aftermarket tractor parts with delivery
MINI HYD EXCAVATOR,

Compatible equipment models: 2332885:

MINI HYD EXCAVATOR  301.4C   301.5   301.7D   301.7D CR   302.2D   302.4D   302.5   302.7D   303.5D   303.5E   303E CR   304D CR   304E   Caterpillar
Number on catalog scheme: 3
 
  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     132-8223     110 volt Power Pack     1    
1U-6221 Torque Wrench     1    
132-8143 36 mm Hex Link     1    
B     138-7573     Link Bracket     2    
C     Forcing screw     24mm x 130mm     1    Start By:
Remove the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Remove".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Thoroughly clean the area around the swing drive prior to removal.
Drain the oil from the swing drive into a suitable container for storage or disposal. The capacity of the swing drive is 8 L (2.1 US gal).
Illustration 1 g00518158
Use Tooling (A) to remove bolts (1) and the washers that secure the swing drive to the main frame.
Illustration 2 g00900976
Fasten Tooling (B) and a hoist to swing drive (2), as shown.
Illustration 3 g00902274
Remove the two corks from the threaded holes in the swing drive housing. Install Tooling (C) in each threaded hole in the swing drive housing. Slowly tighten one forcing screw for a few turns, and then tighten the other forcing screw for a few turns. Tighten the forcing screws evenly in this manner in order to separate the swing drive from the main frame.
Remove swing drive (2) from the machine. The weight of the swing drive is approximately 281 kg (620 lb).

Caterpillar SIS machinery equipment:

Caterpillar SIS
  • 301.5 301.6 301.8 Mini Hydraulic Excavator 3YW00001-UP (MACHINE) POWERED BY 3003 Engine » 233-2885 TOOTH GP
  • 303.5E 2CR Mini Hydraulic Excavator BG800001-UP (MACHINE) POWERED BY C1.7 Engine » 233-2885 TOOTH GP
  • 304E 2CR Mini Hydraulic Excavator CJ200001-UP (MACHINE) POWERED BY C2.4 Engine » 233-2885 TOOTH GP

Caterpillar parts catalog:

Caterpillar parts catalog
303.5E CR Mini Hydraulic Excavator JX200001-UP (MACHINE) POWERED BY C1.8 Engine
301.5 301.6 301.8 Mini Hydraulic Excavator 3YW00001-UP (MACHINE) POWERED BY 3003 Engine
302.5 Mini Hydraulic Excavator 4AZ00001-UP (MACHINE) POWERED BY 3013 Engine
304D CR Mini Excavator TYK00001-UP (MACHINE) POWERED BY S3Q2 Engine
303.5 D Mini Excavator RHP00001-UP (MACHINE) POWERED BY S3Q2 Engine
301.4C Mini Hydraulic Excavator LJK00001-UP (MACHINE)
302.7D CR Mini Hydraulic Excavator LJL00001-UP (MACHINE)
303.5E Mini Hydraulic Excavator RKY00001-UP (MACHINE) POWERED BY C1.8 Engine
304E Mini Hydraulic Excavator TTN00001-UP (MACHINE)
301.7D Mini Hydraulic Excavator LJH00001-UP (MACHINE)
302.4D Mini Hydraulic Excavator LJN00001-UP (MACHINE)
302.2D Mini Hydraulic Excavator LJG00001-UP (MACHINE)
301.7D CR Mini Hydraulic Excavator LJ800001-UP (MACHINE)
303.5E 2CR Mini Hydraulic Excavator BG800001-UP (MACHINE) POWERED BY C1.7 Engine
304E 2CR Mini Hydraulic Excavator CJ200001-UP (MACHINE) POWERED BY C2.4 Engine
303E CR Mini Hydraulic Excavator HHM00001-UP (MACHINE) POWERED BY C1.3 Engine
301.4C Mini Hydraulic Excavator LJ300001-UP (MACHINE)


Parts tooth Caterpillar catalog:

1537881 TOOTH GP-UNI
302.2D, 302.4D, 302.5, 302.5C, 302.7D, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304D CR, 304E, 305, BH150, BH27
1471032 TOOTH GP-UNI
301.4C, 301.5, 301.6C, 301.7D, 301.7D CR
1359380 TOOTH-UNI
301.4C, 301.5, 301.6C, 301.7D, 301.7D CR
2313999 TOOTH
301.4C, 301.5, 301.6C, 301.7D, 301.7D CR, 302.2D, 302.4D, 302.5, 302.5C, 302.7D, 303, 303.5D, 303.5E, 303E CR, 304D CR, 304E
1359390 TOOTH-UNI
302.2D, 302.4D, 302.5, 302.5C, 302.7D, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304D CR, 304E, 305, BH150, BH27
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.