AVSPARE.COM
parts catalog

TRACK GP 1246214 - Caterpillar



1246214 TRACK GP Caterpillar parts 320 L, 320B TRACK
Rating:
60
Alternative (cross code) number:
CA1246214
124-6214
1246214
Caterpillar 1246214 TRACK GP

Buy TRACK GP 1246214 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 1246214:

EXCAVATOR  320 L   320B   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

Calculating Cylinder Liner Projection
The following method for calculating the liner projection is the preferred method under these circumstances:
Single cylinder head joint repair
Engine rebuildNote: When installation of spare used spacer plates and cylinder liners is desired, having the stocked parts measured and matched will reduce repair time.Note: The method of measuring liner projection that uses the 8T-0455 Liner Projection Tool Group can still be used.Regardless of the procedure, the contact surface of the cylinder block for the liner flange and spacer plate must be thoroughly clean before installation of replacement parts.If a new spacer plate and cylinder liner will be installed in the same cylinder, there is no need to calculate the cylinder liner projection. The production process control for the parts is adequate.If a used spacer plate or cylinder liner will be installed, perform the following measurement and calculation procedure.
Table 1
Required Tools    
A     8T-0455 Liner Projection Tool Group    
B     Digital micrometer with a resolution of 0.001 mm    The cylinder liner projection is now a calculation based on measurement of parts that uses the following dimensions:
The average thickness of the flange for the 211-7826 Cylinder Block Liner, measured in four places
The average thickness of the 110-6994 Spacer Plate, measured in four places
The nominal manufactured thickness of a new 144-5692 Plate Gasket A new 144-5692 Plate Gasket must be installed with the spacer plate and cylinder liner.Use the following procedure to calculate the cylinder liner projection.
Illustration 3 g02657236
(X) Average thickness of the spacer plate (Y) Nominal thickness of the spacer plate gasket (Z) Average thickness of the cylinder liner flange
Use tool (B) to measure the thickness of the cylinder liner flange at four equally spaced locations around the circumference of the flange. Determine the average of the measurements.The result is dimension (Z). Mark the result on the cylinder liner with a permanent marker. Do not scribe the material.
Illustration 4 g02657156
Use tool (B) to measure the thickness of the spacer plate at the four locations identified by "X" in Illustration 4. Determine the average of the measurements.The result is measurement (X). Mark the result on the spacer plate with a permanent marker. Do not scribe the material.
Compare the average measurements to the dimensions listed in Table 2.If the average measured dimensions are within the acceptable range, the parts can be installed.If the average measured dimensions are not within the acceptable range, the parts cannot be installed. New parts must be obtained.Note: There is no need to measure the thickness of the 144-5692 Plate Gasket because a new gasket is always installed. The nominal manufacturing dimension is used in the calculation.Note: Reference Test and Adjusting, UENR0519, "Cylinder Liner Projection"
Table 2
Dimensions for Acceptable Cylinder Liner Projection with the 110-6991 Cylinder Head Gasket    
Part     Dimension     Value    
211-7826 Cylinder Block Liner flange    
12.65 0.02 mm (0.498 0.0001 inch)     Z    
110-6994 Spacer Plate    
12.31 0.03 mm (0.4846

Caterpillar SIS machinery equipment:

Caterpillar SIS
  • 320, 320 L, 320 N AND 320 S EXCAVATORS 3XK00822-UP (MACHINE) POWERED BY 3116 ENGINE » 124-6214 TRACK GP
  • 320B, 320B L, 320B LN, 320B N & 320B S Excavators 1XS00001-UP (MACHINE) POWERED BY 3116 Engine » 124-6214 TRACK GP


Parts track Caterpillar catalog:

1156424 TRACK ADJUSTER & RECOIL GP
318B, 320B, 320B L, 320B U, OEMS
1156423 TRACK ADJUSTER & RECOIL GP
318B, 320B, 320B L, 320B U, OEMS
9W9359 TRACK GP
317B LN, 318B, 320, 320 L, 320B, 320N, OEMS
1156422 TRACK ADJUSTER & RECOIL GP
318B, 320B, 320B L, 320B U, OEMS
1941912 TRACK GP
318B, 318C, 319D, 320B, 320B U, 320C, 320C FM, 320C L, 320D, 320D L, 320D LRR, 321B, 321C, 321D LCR, 323D L
1156425 TRACK ADJUSTER & RECOIL GP
318B, 320B, 320B L, 320B U, OEMS
1028165 TRACK ADJUSTER & RECOIL GP
311, 311B, 312, 315, 317, 320 L, 320N, OEMS
1088342 TRACK GP
322 FM L, 325 FM L, 325 L
1210290 TRACK GP
315B L, 315C, 317B LN, 318B, 320 L, 320B, 320C
1177121 TRACK GP
320, 320 L, 320B, 320B FM LL, 320C, 320N
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.