AVSPARE.COM
parts catalog

TUBE AS 1246967 - Caterpillar



1246967 TUBE AS Caterpillar parts M312 TUBE
Rating:
51
Alternative (cross code) number:
CA1246967
124-6967
1246967
Caterpillar 1246967 TUBE AS

Buy TUBE AS 1246967 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEELED EXCAVATOR,

Compatible equipment models: 1246967:

WHEELED EXCAVATOR  M312   Caterpillar
Number on catalog scheme: 13
 
  For full view, you need register

Information:


Illustration 1 g02160341
Schematic of the Cat Data Link CircuitThis failure results in codes that are logged against an ECM that is not communicating some expected information to the LH Operator ECM. The LH Operator ECM cannot communicate with the Engine ECM or the ECM appears to work intermittently. System Response:When this diagnostic code is active, the following occurs:
Engine shutdown due to diagnostic feature is disabled.
Loss of engine data over Cat Data Link.
Operator station fault lamp is active.
The following pop-up message shows on graphical display: "Loss of communication with Engine. Engine features may be disabled"Note: The LH Operator ECM is located under the LH Operator Platform.Test Step 1. VERIFY THE HARDWARE AND THE SOFTWARE PART NUMBERS.
Verify that the following information is correct:
The part number of the software for the LH Operator ECM
The part number of the "Engine ECM software"
The part number of the LH Operator ECM
The part number of the Engine ECMNote: Consult the Business Unit that produces the product for the correct part numbers of the configuration software. Expected Result:All part numbers are correct. Results:
OK - All part numbers are correct. Proceed to test step 2.
NOT OK - All part numbers are NOT correct. The part number of the LH Operator ECM may be incorrect. The part number of the Engine ECM may be incorrect. The incorrect software for the ECM may also be installed. Repair: Replace the incorrect ECM with an ECM that has the correct part number. Flash the correct and most current software. See Troubleshooting, "Electronic Control Module (ECM) - Flash Program".STOPTest Step 2. INSPECT THE HARNESS CONNECTIONS.
Turn the disconnect switch to the OFF position.
Inspect all harness connections that are related to the Cat Data Link. Make sure that the connectors are clean and tight.
Check the connectors for proper mating.
Check the wires at the connector.
Check each wire for nicks or signs of abrasion in the insulation.
Check for moisture at the connector.
Check the connectors for dirty contacts or corroded contacts.
Check each pin and each socket of the machine harness connectors. Expected Result:

Caterpillar parts catalog:

Caterpillar parts catalog
M312 Excavator 6TL00001-00409 (MACHINE) POWERED BY 3054 Engine


Parts tube Caterpillar catalog:

1193662 TUBE-HEAT SHRINK
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B,...
1186693 TUBE AS
M312, M315, M318, M320
1496845 TUBE
M312, M315, M318
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.