AVSPARE.COM
parts catalog

TUBE AS 1694962 - Caterpillar


1694962 TUBE AS Caterpillar parts 973C
Rating:
15
Alternative (cross code) number:
CA1694962
169-4962
1694962
Caterpillar 1694962 TUBE AS
Weight: 4 pounds 2 kg.

Buy TUBE AS 1694962 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK LOADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
The ROP Shop Genuine OEM PTO Switch fits Simplicity 1694943 1694944 1694945 1694961 1694962
$27.49
 

14 Jul 2019

Simplicity: Simplicity
The ROP Shop Genuine OEM PTO Switch fits Simplicity 1694943 1694944 1694945 1694961 1694962
New Genuine OEM PTO SWITCH || Fits Simplicity 1694943 1694944 1694945 1694961 1694962 || No. of Positions - 2, No. of Terminals - 2 || Push/Pull Yellow Knob, Snap Mount || Quality Aftermarket Part with 1 Year Warranty
Number on catalog scheme: 4
 
  For full view, you need register

Compatible equipment models: 1694962:

TRACK LOADER  973C   Caterpillar

Information:

434-3868 Plate - Used to hold the gear segment tool in place and prevent the segment tool from rotation when checking backlash of cam gear.
Illustration 2 g03870106Setting Backlash for Camshaft and Adjustable Idler Gear
Note: The rocker arm bolts must be loosened to remove preload from the camshaft.
Illustration 3 g02685416
Front cover is removed.
With the front cover removed, remove bolts (3), plate (2), and adjustable idler gear (1).
Illustration 4 g02686407
Loosen one bolt and two nuts (4) that secure the stub shaft. Remove the remaining three nuts. The one bolt and two nuts (4) can still be accessed when the gear segment tool is installed.
Illustration 5 g03320498
(5) Timing marks
(6) 374-3473 Gear Gauge
With the flywheel pinned at TDC for cylinder one, align timing marks (5).
Install the cam gear backlash tool onto the stub shaft, as shown. Both sides of the gear segment tool should be engaged with the corresponding gear, as shown. Hand tighten the one bolt and two nuts enough so that slight resistance is felt if the stub shaft is rotated.
Illustration 6 g03870106
The 434-3868 Plate can be installed to hold the gear segment tool in place.
Illustration 7 g02688245
Measure the backlash between camshaft gear (2) and gear segment tool (3). When the gear segment tool is held stationary, the backlash between the gears is 0.356 0.254 mm (0.014 0.010 inch). Lightly tap the stub shaft with a soft mallet to move the gear segment tool closer or further away to the cam gear as necessary. This movement will increase or decrease the amount of backlash.
Illustration 8 g02688540
Once the proper backlash is obtained, tighten the nuts and the bolt (4) to a torque of 55 10 N m (41 7 lb ft).
Illustration 9 g02688598
Remove the cam gear backlash tool.
Clean the studs with a wire brush to remove any old thread lock compound for the three nuts and washers removed in Step 2.
Apply Loctite 242 to the studs.
Install the 3 nuts and washers that were removed and torque to 55 10 N m (41 7 lb ft).
Remove the bolt, two nuts, and two washers that were tightened in Step 6.
Clean the bolt and two studs of any old thread lock compound using a wire brush.
Apply Loctite 242 to the bolt and the two studs.
Install the bolt and two nuts with washers. Torque the bolt and nuts to 55 10 N m (41 7 lb ft).
Illustration 10 g02688636
Install idler gear (1). Verify that the correct amount of backlash is still correct. The mark on the camshaft gear should still align with the mark on the front housing.
Install plate (2). Before installing bolts (3), clean the bolts with a wire brush to remove the old thread lock compound. Apply Loctite 242 to the threads of the bolts and install the bolts. Then, tighten to the proper torque.
Install the front cover. Refer to Disassembly and Assembly, "Housing (Front) - Install".

Caterpillar parts catalog:

Caterpillar parts catalog
973C Custom Parts Manual Track-Type Loader Steel Mill 3RZ00001-UP (MACHINE) POWERED BY 3306 Engine
973C Track-Type Loader Hydrostatic Drive 3RZ00001-UP (MACHINE) POWERED BY 3306 Engine
973C Track-Type Loader BCP00001-UP (MACHINE) POWERED BY C-9 Engine
973C TRACK-TYPE LOADER LDX00001-UP (MACHINE) POWERED BY C9 Engine


Parts tube Caterpillar catalog:

7X2049 TUBE AS-REFRIGERANT ORIFICE
120H, 120H ES, 120H NA, 12H, 12H ES, 12H NA, 135H, 135H NA, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16H, 307B, 317B LN, 318B, 322B L, 325B L, 330B L, 345B, 34...
1979367 TUBE AS
12H, 140M, 140M 2, 160M, 160M 2, 2290, 2390, 2391, 2491, 2590, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 511, 521...
1932162 TUBE AS
12H, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 340D L, 627G, 637D, 637G, 973C, 973D, C-9, C9, D6R II, M330D, MTC735, TK711, TK721, TK722, TK732, T...
2633464 TUBE AS
627G, 627H, 627K LRC, 637D, 637E, 637G, 973C, 973D, C-9, C9, CX31-C9I, D6R, D6R II, D6R III, D6R STD, D6T, D7E, D7R XR, TH31-E61
8G3929 TUBE
973, 973C, 973D
3G5978 TUBE
963, 963B, 963C, 973, 973C
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.