AVSPARE.COM
parts catalog

TUBE AS 1C4157 - Caterpillar



1C4157 TUBE AS Caterpillar parts AP-1200 TUBE
Rating:
43
Alternative (cross code) number:
CA1C4157
1C-4157
1C4157
Caterpillar 1C4157 TUBE AS
Weight: 0.21 pounds 0 kg.

Buy TUBE AS 1C4157 Caterpillar genuine, new aftermarket tractor parts with delivery
ASPHALT PAVER,

Compatible equipment models: 1C4157:

ASPHALT PAVER  AP-1200   Caterpillar
Number on catalog scheme: 2
 
  For full view, you need register

Information:

Start By:
Remove the front idler and the recoil spring assembly.
The spring of the recoil spring assembly is compressed under several tons of force.Do not attempt to compress or release the tension of the spring with the nut on the end of the retaining rod.Damaged threads on the retaining rod or nut can cause the assembly to come apart with force, resulting in injury or death.
Prior to disassembling the recoil spring assembly, make sure that Tooling (A) is on a level surface.
Thoroughly clean the outside surface of the recoil spring assembly prior to disassembly.
Illustration 1 g00483426
Install Tooling (C) on Tooling (B), as shown.
Illustration 2 g00494710
Illustration 3 g00483437Note: Two adjustable supports (1), reaction plate (2) and movable plate (3) are part of Tooling (A).
Adjust the spacing between reaction plate (2) and movable plate (3). The spacing is approximately the same length as the recoil spring assembly (free length). Also, make sure that two adjustable supports (1) are positioned between the reaction plate and the movable plate, as shown. Level the two supports.Note: The recoil spring assembly may be installed in Tooling (A) from the end. In this case, reaction plate (2) must be removed. Then reinstall the reaction plate after the recoil spring assembly is in place on two adjustable supports (1).
Do not remove the hoist from the recoil spring assembly until the unit is leveled, centered and locked in the specified tooling.
The combined weight of the recoil spring assembly is approximately 116 kg (255 lb).
Fasten a suitable lifting device to the recoil spring assembly. Put the recoil spring assembly in position on two adjustable supports (1) in Tooling (A).
Adjust the two adjustable supports to align the centerline of the recoil spring assembly with the centerline of Tooling (A).
Illustration 4 g00498760
The hoist has been removed from the recoil spring assembly to provide a better illustration of level gauge (4).
Put a level gauge (4) on the recoil spring assembly.
Illustration 5 g00498781
Reposition the recoil spring assembly until the recoil spring assembly is level. Reposition the recoil spring assembly until the retaining rod and nut (6) are centered in the hole in reaction plate (2).
The recoil spring assembly is leveled by moving adjustable supports (1) higher or lower. After the recoil spring assembly is leveled and centered, install two pins (5) on the back side of reaction plate (2), as shown.
Operate Tooling (B) enough to hold the recoil spring assembly in position between reaction plate (2) and movable plate (3). Make sure that the recoil spring assembly is level and centered.
Illustration 6 g00498784
Several tons of force are required to compress the recoil spring during assembly.Do not compress the spring assembly until the covers on the tooling have been closed.It is possible for the recoil spring to twist under load and come out of the tooling resulting in injury or death.
Close covers (7) on Tooling (A). Use Tooling (B) to compress the recoil spring assembly slightly.
Illustration 7 g00889063
Through the opening in the end of Tooling (A), remove the socket head bolts and lock strip (8) from the end of the retaining

Caterpillar parts catalog:

Caterpillar parts catalog
AP-1200 ASPHALT PAVER 2JD00001-UP (MACHINE) POWERED BY 6.354 ENGINE


Parts tube Caterpillar catalog:

8C7613 TUBE
AP-1000, AP-1000B, AP-1050, AP-1055B, AP-1055D, AP-1200, AP-600D, AP-650B, AP-655C, AP-655D, AP-800, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-2455C, BG-2455D, BG-245C,...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.