AVSPARE.COM
parts catalog

TUBE 2333896 - Caterpillar



2333896 TUBE Caterpillar parts TUBE
Rating:
26
Alternative (cross code) number:
CA2333896
233-3896
2333896
Caterpillar 2333896 TUBE

Buy TUBE 2333896 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Removal Procedure
Start By:
Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00537836
Remove two nuts (1), the washers and the heat shield from the exhaust manifold.
Illustration 2 g00537855
Remove bolt (3) from the bracket that holds two of the fuel injection lines in position. Loosen nuts (2) and (4) and remove the two fuel injection lines from the engine. Put protective caps on the fuel injectors and put protective caps on the fuel injection pump in order to prevent contamination.
Illustration 3 g00537885
Remove the remaining ten exhaust manifold nuts (5) and the large washers. Remove exhaust manifold (6).
Illustration 4 g00541058
Remove three exhaust manifold gaskets (7) from the cylinder head and the twelve exhaust manifold studs, if necessary. Make sure that the position of the two longer studs are marked for proper installation.Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Description     Qty    
A     5P-0144     Fuel Line Socket     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the twelve exhaust manifold studs were removed, apply 5P-3931 Anti-Seize Compound to both ends of the exhaust manifold studs and install the studs in the cylinder head. Make sure that the two longer studs are installed in the correct position. Tighten the studs to a torque of 27 4 N m (20 3 lb ft).
Illustration 5 g00541058
Put three exhaust manifold gaskets (7) in position on the cylinder head.
Illustration 6 g00537885
Install exhaust manifold (6). Install ten washers and nuts (5). The two longer studs are for the installation of the heat shield. Tighten exhaust manifold nuts (5) to a torque of 47 4 N m (35 3 lb ft).
Illustration 7 g00537855
Remove the protective caps from the fuel injectors and the fuel injection pump. Put the fuel injection lines in position and tighten nuts (2) and (4) finger tight. Install bolt (3) in the bracket that holds the fuel injection lines in position. Tighten nuts (3) and (4) with Tool (A) to a torque of 40 7 N m (30 5 lb ft).
Illustration 8 g00537836
Install the two large washers and the spacers on the two remaining exhaust manifold studs. Install heat shield (1) and the remaining two washers and exhaust manifold nuts that fasten heat shield (1) to the exhaust manifold. Tighten the two nuts to a torque of 47 4 N m (35 3 lb ft).
Prime the fuel system. Refer to the Operation and Maintenance Manual, "Fuel system - Prime" topic (Maintenance Section).End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.