AVSPARE.COM
parts catalog

TUBE AS 3157230 - Caterpillar



3157230 TUBE AS Caterpillar parts TUBE
Rating:
51
Alternative (cross code) number:
CA3157230
315-7230
3157230
Caterpillar 3157230 TUBE AS

Buy TUBE AS 3157230 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Remove the top two bolts (53) from input transfer gear case (52).
Install Tooling (C) into the top two threaded holes in input transfer gear case (52).
Illustration 23 g02518776
Disconnect all harness assembly clips (54) that attach harness assembly (50) to the transmission. Disconnect harness assembly (50).
Illustration 24 g02518818
Disconnect tube assembly (55). Disconnect hose assembly (56).
Illustration 25 g02519560
Disconnect speed sensors (58) from harness assembly (50). Disconnect level sensor (59) from harness assembly (50). Disconnect all harness clips (57) and set harness assembly (50) out of the way.
Illustration 26 g02519243
Disconnect hose assemblies (60), (61), (62), and (63).
Illustration 27 g02519801
Illustration 28 g02519860
Attach Tooling (E) and a suitable lifting device to center drive shaft (66) in order to support center drive shaft (66). The weight of center drive shaft (66) is approximately 113 kg (250 lb).
Remove bolts (65) that attach center drive shaft (66) to output yoke (64).
Retract center drive shaft (66) and allow center drive shaft (66) to rest on suitable cribbing.
Illustration 29 g02519937
Disconnect hose assembly (67) from the bottom of the output transfer gear case.
Illustration 30 g02527538
Typical Example
Attach a suitable lifting device to Tooling (C) at the rear of transmission (68). Attach Tooling (D) and a suitable lifting device to the front lifting brackets on transmission (68). Attach Tooling (D) onto the suitable lifting device of Tooling (C). The combined weight of transmission (68) and the transfer gears is approximately 2660 kg (5865 lb).
Illustration 31 g02527597
Right Side
Remove bolts (69) and bolt (70) from both sides of the transmission.
Illustration 32 g02527623
Left Side
Use Tooling (C), Tooling (D), and the suitable lifting device in order to slightly raise the transmission and the transfer gears off the mounts. Refer to Illustration 30.
Remove bolts (71).
Use two people in order to remove mounting bracket (72) from the output transfer gear case. The weight of mounting bracket (72) is approximately 32 kg (70 lb).
Repeat Steps 39 and 40 for the opposite side of the machine.
Illustration 33 g02527719
Right Side
Remove four bolts (73).
Use two people in order to remove mounting bracket (74) from the input transfer gear case. The weight of mounting bracket (74) is approximately 25 kg (55 lb).
Repeat Steps 42 and 43 for the opposite side of the machine.
Illustration 34 g02527863
Typical Example
Illustration 35 g02527876
Typical Example
Use Tooling (C), Tooling (D), and the suitable lifting device in order to remove transfer gears and transmission (68). Adjust the angle of Tooling (D) as transfer gears and transmission (68) are being removed.


Parts tube Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.