AVSPARE.COM
parts catalog

TUBE AS 3157348 - Caterpillar



3157348 TUBE AS Caterpillar parts TUBE
Rating:
11
Alternative (cross code) number:
CA3157348
315-7348
3157348
Caterpillar 3157348 TUBE AS

Buy TUBE AS 3157348 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g02594937
Connections of the Machine Power Distribution RelayThis diagnostic code is associated with the Machine Power Distribution Relay. The FMI 05 diagnostic code is recorded when the ECM reads the current of the relay as below normal (open circuit).The possible causes of this diagnostic code are listed below:
The energizer circuit of the relay is open.
The return circuit of the relay is open.
The relay has failed.
The ECM has failed. This failure is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 3470 FMI 05 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.Test Step 1. CHECK THE RELAY.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine. Ensure that the diagnostic code for the relay is active.
Disconnect the machine harness from the relay.
At the machine harness connector for the relay that is being tested, install a jumper wire. Install a jumper wire from the signal wire (X721-BR) to ground (wire P990-BR).
Observe the status of the diagnostic code. The diagnostic code is active or the diagnostic code is NOT active.Expected Result:The status of the diagnostic code is active. The status of the diagnostic code is NOT active as the jumper is installed and then removed.Results:
YES - The circuit is correct.Repair: The relay has failed. Replace the relay.STOP
NO - The diagnostic code remains active. Proceed to Test Step 2.Test Step 2. CHECK THE RELAY CIRCUIT FOR AN OPEN.
The jumper that is between the signal wire and the return wire remains installed.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector J2 from the ECM.
At the J2 machine harness connectors for the ECM, measure the resistance from contact J2-6 for the relay to ground (wire P990-BR).Expected Result:There should be continuity (less than 5.0 ohms resistance).Results:
YES - The machine harness is correct. Proceed to Test Step 3.
NO - There is an open circuit in the machine harness.Repair: The open circuit is in the signal wire (X721-BR) or in ground wire (P990-BR) of the machine harness. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the harness connectors. Clean the contacts of the harness connectors. Check the wires for damage to the insulation that can be caused by excessive heat, corrosion, or chafing.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit.
Reconnect all harness connectors. Make sure that the connectors are fully seated and locked.
Turn the disconnect switch and the key start switch to the ON position.
Clear all of the inactive diagnostic codes.
Operate the machine.
Stop the machine and place the parking brake switch in the ON position.
Observe the status of the diagnostic code. The diagnostic code is active or the diagnostic code is NOT active.Expected Result:The diagnostic code is


Parts tube Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.