AVSPARE.COM
parts catalog

TUBE AS 3535201 - Caterpillar



3535201 TUBE AS Caterpillar parts 621H, 621K, 623H, 623K, 623K LRC TUBE
Rating:
11
Alternative (cross code) number:
CA3535201
353-5201
3535201
Caterpillar 3535201 TUBE AS
Weight: 6 pounds 2 kg.

Buy TUBE AS 3535201 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL TRACTOR, WHEEL TRACTOR-SCRAPER,

Compatible equipment models: 3535201:

WHEEL TRACTOR  621H   623H  
WHEEL TRACTOR-SCRAPER  621K   623K   623K LRC   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:


Stop the engine, lower the bucket to the ground, move the control levers backward and forward to release the pressure in the hydraulic system. Slowly loosen the cap to release any pressure in the hydraulic tank. Let the hydraulic oil become cool before any lines are disconnected in the hydraulic system.
1. Drain the oil from the hydraulic tank. 2. Remove bolt (1) and the large washer. 3. Install washers (2) as needed. Install bolt. Hit the bolt with a hammer to loosen the taper on the pin. Remove the pin. 4. Remove four washers (3), two on each side of the cylinder rod. 5. Disconnect hydraulic line (4).6. Remove pin (5) from the head of steering cylinder. 7. Disconnect hydraulic line (6) from the steering cylinder. 8. Connect a hoist to the bores at the rod and head ends of cylinder (7). 9. Move the cylinder toward the back and out of the machine. The weight of the cylinder is 120 lb. (54 kg).Install Steering Cylinders
1. Put cylinder (1) in position in the machine. 2. Install four washers (2) between the frame and the cylinder rod. 3. Put pin (3) in position and install the washer and bolt. Tighten the bolt to a torque of 150 20 lb.ft. (205 25 N m).4. Install the pin, washer and bolt in the rear bore. Tighten the bolt to a torque of 150 20 lb.ft. (205 25 N m). Make sure the O-ring seals are in position in lines (4) and (5). 5. Put line (4) in position and install the flanges and bolts. 6. Connect line (5).7. Fill the hydraulic tank to the correct level with hydraulic oil. See MAINTENANCE GUIDE.end by:a) separation of anti-pivot linkDisassemble Steering Cylinders
start by:a) remove steering cylinders 1. Remove seals (1) from the rod end of the cylinder. 2. Put tooling (A) in position and remove the bearing.3. Do Steps 1 and 2 for the head end of the cylinder if necessary. 4. Fasten the rod end of steering cylinder (2) to tooling (B).5. Slowly extend the cylinder to drain the oil from the cylinder.6. Install support (5) under the rod and fasten strap (4) to hold the rod on the support.7. Remove head bolts (3). Pull the cylinder away from the rod and head with tooling (B). 8. Use tooling (C) to remove the nut that holds the piston on the rod. 9. Remove piston (6) from the rod. 10. Remove seal assembly (8) and wear sleeve (7) from the piston. 11. Remove head (9) from the cylinder rod. 12. Remove O-ring seal (10) and back-up ring (11) from the head. 13. Remove seals (12), (13) and (14) from the cylinder head.Assemble Steering Cylinders
TYPICAL EXAMPLE1. Install inner seal (4) in head (1). The inner seal does not have a lip and can be installed either way. Install middle seal (3) with the lip in. Use tooling (B) and install outer seal (2) with the lip out. Put clean oil on

Caterpillar parts catalog:

Caterpillar parts catalog
621H Wheel Tractor Scraper DBK00001-UP (MACHINE) POWERED BY C13 Engine
623H Wheel Tractor Scraper DBF00001-UP (MACHINE) POWERED BY C13 Engine
621H Wheel Tractor Scraper EAZ00001-UP (MACHINE) POWERED BY C13 Engine
623H Wheel Tractor Scraper EJD00001-UP (MACHINE) POWERED BY C13 Engine
621K Wheel Tractor-Scraper WTA00001-UP (MACHINE) POWERED BY C13 Engine
623K Wheel Tractor-Scraper WTB00001-UP (MACHINE) POWERED BY C13 Engine
621K Wheel Tractor-Scraper WTL00001-UP (MACHINE) POWERED BY C13 Engine
623K Wheel Tractor-Scraper WTM00001-UP (MACHINE) POWERED BY C13 Engine


Parts tube Caterpillar catalog:

3286414 TUBE AS
621H, 621K, 623H, 623K, 623K LRC
3670854 TUBE AS
621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC
3670853 TUBE AS
621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC
3529995 TUBE AS
621H, 621K, 627H, 627K, 627K LRC
3529994 TUBE AS
621H, 621K, 627H, 627K, 627K LRC
3264952 TUBE AS
621H, 623H, 627H
3614734 TUBE AS
621H, 623H, 627H
3674904 TUBE AS
621H, 623H, 627H
3070348 TUBE
621H, 621K, 623H, 623K, 623K LRC
3965566 TUBE AS
349E, 349E L, 349E L HVG, 349E L VG, 621H, 623H, 627H
3640896 TUBE AS
349E, 349E L, 349E L HVG, 349E L VG, 621H, 623H, 627H
3640895 TUBE AS
349E, 349E L, 349E L HVG, 349E L VG, 621H, 623H, 627H
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.