AVSPARE.COM
parts catalog

TUBE AS 3598591 - Caterpillar



3598591 TUBE AS Caterpillar parts 390D, 390D L, 390F L TUBE
Rating:
31
Alternative (cross code) number:
CA3598591
359-8591
3598591
Caterpillar 3598591 TUBE AS
Weight: 37 pounds 17 kg.

Buy TUBE AS 3598591 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 3598591:

EXCAVATOR  390D   390D L   390F L   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:

Introduction
This Special Instruction is used to inspect the following items: air inlet heater, air inlet heater solenoid and the solenoid connections.Inspection Points
Look at the power terminals of the relay for any melted insulators or damaged insulators.
Inspect power terminals on the relay for damage. A damaged terminal stud will be blackened or able to move freely. Remove the relay and replace the relay if damage is found.
Look for missing isolation mounts. Also, look for worn isolation mounts or damaged isolation mounts.
The routing of the power cable should not create a force on the isolation mount on the relay. Provide relief for any items that inhibit the ability of the mounts to isolate the relay from vibration or shock. This may require additional mounting points at the relay or near the relay. A longer wire from the relay to the heater element will also remedy the issue. Power leads must be supported within six to eight inches of the terminal connection at the relay.
Look for any abnormal wear and repair any abnormal wear to the wires that are connected to the relay. The following areas should be inspected: battery, cables for the air inlet heater and control circuit of the Electronic Control Module (ECM)
Terminals should be clean. Clean terminals will provide a good electrical connection to the cables.
Remove the air inlet heater and replace the air inlet heater if the heater assembly or the elbow shows signs of damage. Damage to the air inlet heater includes brown shading of the paint instead of yellow. Torque Requirements
Illustration 1 g01717059
Torque nut (2) to 9 1 N m (7 1 lb ft). Hold nut (6) with an additional wrench as you are applying torque to nut (2) .
Torque isolation mount (5) to 12 1 N m (9 1 lb ft).
Torque mounting hardware (1) to 55 9 N m (41 7 lb ft).Note: Secure the wire with the clip before applying the proper torque of 2.25 0.25 N m (20 2 lb in) to nut (3) as you are holding nut (4) with a wrench.Wire terminal nuts and locking washers are supplied with the relay. Caterpillar recommends the use of a torque wrench such as the Mountz TLS-1360 torque wrench. Note: Not meeting the specified torque limit may cause electrical arcing due to a mechanical failure of the stud on the relay or a loose connection.Wire Size, Terminal Size, Boot Selection and Routing
A boot must be installed on all electrical connections to the air inlet heater relay

Caterpillar parts catalog:

Caterpillar parts catalog
390F L Excavator HNG00001-UP (MACHINE) POWERED BY C18 Engine
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine
390D L Excavator WAG00001-UP (MACHINE) POWERED BY C18 Engine
390D L Excavator WBT00001-UP (MACHINE) POWERED BY C18 Engine
390D L Excavator WAP00001-UP (MACHINE) POWERED BY C18 Engine
390D Excavator BYP00001-UP (MACHINE) POWERED BY C18 Engine
390D Excavator KCZ00001-UP (MACHINE) POWERED BY C18 Engine
390F L Excavator MGF00001-UP (MACHINE) POWERED BY C18 Engine
390F L Excavator HSM00001-UP (MACHINE) POWERED BY C18 Engine
390F L Excavator TYE00001-UP (MACHINE) POWERED BY C18 Engine
390F L Excavator GAY00001-UP (MACHINE) POWERED BY C18 Engine
390F L Excavator HJD00001-UP (MACHINE) POWERED BY C18 Engine
390F Mobile Hydraulic Power Unit B3700001-UP (MACHINE) POWERED BY C18 Engine
390F L Excavator YHT00001-UP (MACHINE) POWERED BY C18 Engine


Parts tube Caterpillar catalog:

1688974 TUBE AS
24M, 365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 651B, 657E, 657G, 824C, 834G, 834H, 836...
2748359 TUBE AS
24M, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 631E, 631G, 633E II, 637E, 637G, 657E, 657G, 772, 772G, 772G OEM, 834H, 834K, 836H, 836K, 988H, 988K, AD45B, AD55, C18, C18 I6, CX31-C18I, ...
2203496 TUBE AS
365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L
2270684 TUBE AS
365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L
2012978 TUBE AS
365C, 385B, 385C, 385C L, 390D, 390D L, 390F L
3029217 TUBE AS
385B, 385C, 385C L, 390D, 390D L, 390F L
3729810 TUBE AS
390D, 390D L, 390F L
2825848 TUBE AS
390D, 390D L, 390F L
3569237 TUBE AS
390D, 390D L, 390F L
3569235 TUBE AS
390D, 390D L, 390F L
3587375 TUBE AS
390D, 390D L, 390F L
3587374 TUBE AS
390D, 390D L, 390F L
3598590 TUBE AS
390D, 390D L, 390F L
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.