AVSPARE.COM
parts catalog

TUBE AS 3598685 - Caterpillar



3598685 TUBE AS Caterpillar parts 390D, 390D L TUBE
Rating:
41
Alternative (cross code) number:
CA3598685
359-8685
3598685
Caterpillar 3598685 TUBE AS
Weight: 39 pounds 17 kg.

Buy TUBE AS 3598685 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 3598685:

EXCAVATOR  390D   390D L   Caterpillar
Number on catalog scheme: 15
 
  For full view, you need register

Information:


Illustration 3 g01675118
(2) Retention spring
Disconnect the gas springs (1) from the hood. Open the hood and remove the retention spring (2) from the hood side of the gas spring. Be careful not to lose the clip. Pull the strut off the ball joint. Rest the strut out of the way. Disconnect the gas springs from both side of the hood.
Illustration 4 g01675120
(3) Hinge bolts
Illustration 5 g01683293
(3) Hinge bolts
Close the hood. Remove the hinge bolts (3) from both sides of the vehicle. Unlatch the hood. Remove the hood. Cab doors can be removed if this helps with the removal. Adjustment or Assembly of New Hood
Illustration 6 g01675124
(4) Hood
Place the new hood (4) onto the machine. Make sure that the new hood is centered around the grill and around the muffler.
Illustration 7 g01675126
The gap between the hood and the horizontal face of the counterweight should be 20 mm (0.79 inch) on all sides. Use spacers to set this gap.
Illustration 8 g01675131
Use a spacer to create a 50 mm (1.97 inch) gap between the hood and the frame. Repeat for the other side of the machine.
Illustration 9 g01675134
Corners
Reassemble the gas springs to both sides of the hood. The corner that is shown in figure 9 may be pulled in toward the center of the machine. This may cause fouling on the frame or the counterweight as the hood closes. The corner may need to be pulled out further while the hinge bolts are being tightened. This action will slightly twist the hinge. The corner of the hood will be pushed away from the frame. Make sure that the gap between the hood and the horizontal face of the counterweight is still approximately 20 mm (0.79 inch). The hinges may need to be adjusted to a slightly higher position. Repeat for the other side of the machine.
Illustration 10 g01675137
Inside edge
The hinges may not be level at the top of the firewall. In order to maintain the height and alignment of the hood, the inside edge should be level.Adjust the latch
Illustration 11 g01675209
(5) Striker
Illustration 12 g01675210
(5) Striker
When the new hood is in place, the latch on the hood may not align with the mating half of the counterweight. Adjustment can be done at the striker (5) on the counterweight.Adjusting the Corner Caps
Illustration 13 g01675218
(6) Mounting plate
In order to align with the hood, the position of the corner caps can be adjusted. The mounting plate (6) for the frame of the corner cap can be repositioned. Loosen the mounting bolts and position the mounting plate. Repeat for the other side of the machine.Adjustment of the Side Doors
Illustration 14 g01675235
(7) Latch plate
In order to align with the hood and corner caps, the side doors can be adjusted. The latch plate (7) for the locking barrel may also need to be adjusted. Repeat for the other side of the machine.

Caterpillar parts catalog:

Caterpillar parts catalog
390D L Excavator WAG00001-UP (MACHINE) POWERED BY C18 Engine
390D L Excavator WBT00001-UP (MACHINE) POWERED BY C18 Engine
390D L Excavator WAP00001-UP (MACHINE) POWERED BY C18 Engine
390D Excavator KCZ00001-UP (MACHINE) POWERED BY C18 Engine


Parts tube Caterpillar catalog:

2748359 TUBE AS
24M, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 631E, 631G, 633E II, 637E, 637G, 657E, 657G, 772, 772G, 772G OEM, 834H, 834K, 836H, 836K, 988H, 988K, AD45B, AD55, C18, C18 I6, CX31-C18I, ...
3174860 TUBE AS
312D2, 385B, 385C, 385C L, 390D, 390D L, 390F L
1120541 TUBE
350, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 390D, 390D L, 390F L, 5080
3148099 TUBE AS
385C, 385C FS, 385C L, 385C L MH, 390D, 390D L
3029215 TUBE AS
385B, 385C, 385C L, 390D, 390D L
2012981 TUBE AS
365C, 385B, 385C, 385C L, 390D, 390D L, 390F L
3061557 TUBE AS
385C, 385C L, 390D, 390D L
3334591 TUBE AS
390D, 390D L, 390F L
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.