AVSPARE.COM
parts catalog

TUBE AS 3598818 - Caterpillar



3598818 TUBE AS Caterpillar parts 314D LCR TUBE
Rating:
42
Alternative (cross code) number:
CA3598818
359-8818
3598818
Caterpillar 3598818 TUBE AS
Weight: 2 pounds 1 kg.

Buy TUBE AS 3598818 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 3598818:

EXCAVATOR  314D LCR   Caterpillar
Number on catalog scheme: 28
 
  For full view, you need register

Information:

1. Remove bolts (1) from the alternator bracket (if equipped).2. Remove the bolts that hold plate (3), and remove the plate.3. Disconnect water line (2) from the air compressor (if equipped). Turn the water line tee toward the lifting bracket in order to provide clearance to remove the head bolt. 4. Remove bolts (4) and (5) that hold the cylinder head assembly to the cylinder block.5. Fasten a hoist, and remove the cylinder head assembly. The weight is approximately 135 kg (300 lb).
Do not put the cylinder head assembly down on a flat surface. This can cause damage to the fuel injection valves.
6. Remove the gasket and seals from the spacer plate.Install Cylinder Head Assembly
Be sure a new gasket has been installed between the spacer plate and the cylinder block. See Remove & Install Spacer Plate. 1. Thoroughly clean the spacer plate and the bottom surface of the cylinder head assembly. Install a new head gasket, new seals (1) and two O-ring seals (2). 2. Fasten a hoist, and put cylinder head assembly (3) in position on the cylinder block.
(1) Large bolts (3/4in). Put 6V-4876 Molycoat Paste Lubricant on bolt threads and between washer and underside of bolt heads.(2) Small bolts (3/8in). See Step h.3. Put clean engine oil on the threads of the cylinder head bolts. Install the cylinder head bolts and washers. Tighten the bolts in sequence shown in illustration D11970.a. Tighten bolts 1 through 14 in number sequence to a torque of 270 25 N m (200 20 lb ft).b. Tighten bolts 1 through 14 in number sequence to a torque of 470 20 N m (345 15 lb ft)c. Tighten bolts 1 through 14 in number sequence to a torque of 470 20 N m (345 15 lb ft)by hand.d. Install the rocker shaft assemblies and push rods. See the topic "Install Rocker Shaft Assemblies & Push Rods".e. Tighten bolts 15 through 26 in number sequence to a torque of 270 25 N m (200 18 lb ft).f. Tighten bolts 15 through 26 in number sequence to a torque of 450 20 N m (330 15 lb ft).g. Tighten bolts 15 through 26 in number sequence to a torque of 450 20 N m (330 15 lb ft).by hand.h. Tighten the 3/8" bolts to a torque of 45 7 N m (33 5 lb ft). If the studs for the exhaust manifold were removed, install new studs, and tighten them to a torque of 25 4 N m (18 3 lb ft).4. Make an adjustment to the valves to have a clearance of 0.38 mm (.015 in)for intake and 0.76 mm (.030 in)for exhaust. Tighten the locknuts for the valve adjustment screws to a torque of 28 4 N m (21 3 lb ft).5. Install the

Caterpillar parts catalog:

Caterpillar parts catalog
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine


Parts tube Caterpillar catalog:

5I4940 TUBE
311, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D F...
2887698 TUBE AS
311D LRR, 312D, 312D L, 312D2, 312E, 312E L, 314D CR, 314D LCR
3937868 TUBE AS
311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR
3284828 TUBE AS
314D CR, 314D LCR
2181154 TUBE AS
314C, 314D CR, 314D LCR
2827510 TUBE AS
314D CR, 314D LCR, 314E CR, 314E LCR
2452338 TUBE AS
314C, 314D CR, 314D LCR, 314E CR, 314E LCR
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.