AVSPARE.COM
parts catalog

TUBE AS 3598823 - Caterpillar



3598823 TUBE AS Caterpillar parts TUBE
Rating:
31
Alternative (cross code) number:
CA3598823
359-8823
3598823
Caterpillar 3598823 TUBE AS

Buy TUBE AS 3598823 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Image2.4.1
REWORK ? 3516B WASTEGATE COOLING LINES
If the inspection has determined that this rework is needed, replace the tubes at the wastegate with hoses as described below. See images following the instructions for additional details.
1. Remove the tube and fitting that is attached at the right side of the wastegate. Replace the fitting with 2T-2171 elbow with 6V-8398 seal. Replace the tube assembly with a 287-0417 tube assembly with 6V-8398 seal and 267-2217 hose assembly. Use a 124-0174 clip with 191-1442 spacer, 0T-0065 bolt and 5M-2894 washer to secure the 287-0417 tube assembly at the back of the air manifold (see image 2.6.1 and 2.7.1).
2. Remove the coolant return tube from the tee at the the left side of the wastegate. Replace the tube assembly with a 287-0416 tube assembly with 6V-8398 seal and 267-2217 hose assembly. Use one 8M-2770 clip to secure the 287-0416 tube assembly to the outboard side of the 238-7840 bracket assembly (see image 2.6.1 and image 2.7.1).
Image2.6.1
3. Remove the vent tube from the 148-8444 tee at the left side of the wastegate. Orient the 148-8444 tee that attaches at the vent line so it is pointing straight down instead of back towards the wastegate (see image 2.7.1). Install 8C-8989 elbow with 6V-8398 seal on the vent tee and install a 267-2217 hose assembly between the elbow and the tee at the wastegate. Orient the elbow and hose assembly as shown in image 2.7.1.
Image2.7.1
REWORK ? 3516B LEFT AND RIGHT TURBO COOLING RETURN LINES
If the inspection has determined that this rework is needed, replace left and right turbo cooling return lines as described below. See images beneath the instructions for additional details.
1. Remove the coolant return line between the left turbo coupling and the 150-3057 tee. The clip that supported the line will not be reused but the hardware will be reused to install a two piece clamp.
2. Remove the coupling at the left turbo and replace with a 254-4100 coupling with 5K-9090 seal and 6V-1903 seal.
3. Install a 254-4101 coupling assembly at the 150-3057 tee. Use the hardware from step 1 with 6K6535 and 6K-6536 two piece clip to secure the coupling to the 238-7840 bracket assembly.
4. Install 263-2569 tube assembly with with 7L-4773 seal between the coupling at the turbo and the coupling assembly at the tee.
Image2.9.1
5. Remove the coolant return line between the right turbo coupling and the 148-8429 tee.
6. Remove the coupling at the right turbo and replace with a 254-4100 coupling with 5K-9090 seal and 6V-1903 seal.
7. Install a 254-4101 coupling assembly at the 148-8429 tee.
8. Install 263-2570 tube assembly with with 7L-4773 seal between the coupling at the turbo and the coupling assembly at the tee.
Image2.10.1
REWORK ? 3516B TURBO COOLING LINES SUPPORT CLAMPS
If the inspection has determined that this rework is needed, replace the turbo cooling line support clamps at the rear of the engine as described below. See image 2.12.1 for additional details.
1. Remove the metal clips and bracket that are securing the left and right turbo cooling lines.


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.