AVSPARE.COM
parts catalog

TUBE AS 3598824 - Caterpillar



3598824 TUBE AS Caterpillar parts TUBE
Rating:
36
Alternative (cross code) number:
CA3598824
359-8824
3598824
Caterpillar 3598824 TUBE AS

Buy TUBE AS 3598824 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


ACTION REQUIRED
Follow this procedure to update the EMCP3 with new software
1. Stop the Genset if it is running. Reference the appropriate documentation for this step.
2. Connect the Communication Adaptor to the Service Connector on EMCP Control Panel. (For electronic engines the Engine Control Must be powered down)
3. Use Caterpillar Electronic Technician (ET), minimum 2006B version 1.0, to perform a Copy Configuration of the EMCP3 control.
4. Flash the appropriate new EMCP3 software. See TABLE 1 for EMCP3.2 and TABLE 2 for EMCP3.3
NOTE - Special cases:
i)If the Genset has Software part number 266-5553, please see Special Instructions REHS3671.
ii)If the Genset is an MUI engine the previous Software needs to be updated to Oct 2006 Software, and the sensor map number 2 needs to be programmed. Please see Special Instructions REHS3671.
5. Disconnect Service Connector. (Repower Engine Control on Electronic Engines)
Image1
Image2
OWNER NOTIFICATION
U.S. and Canadian owners will receive the attached Owner Notification.
SERVICE CLAIM ALLOWANCES
Caterpillar Dealer Suggested Customer Suggested
Parts % Labor Hrs% Parts % Labor Hrs% Parts % Labor Hrs%
*******Group 1*******
100% 100% 0% 0% 0% 0%
This is a 0.5-hour job for Group 1
Caterpillar Dealer Suggested Customer Suggested
Parts % Labor Hrs% Parts % Labor Hrs% Parts % Labor Hrs%
*******Group 2*******
100% 100% 0% 0% 0% 0%
This is a 0.5-hour job for Group 2
PARTS DISPOSITION
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
MAKE EVERY EFFORT TO COMPLETE THIS PROGRAM AS SOON AS POSSIBLE.
Priority - PRODUCT IMPROVEMENT PROGRAM FOR UPDATING SOFTWARE FOR EMCP 3.2 AND EMCP 3.3 CONTROLS, PART NUMBERS 227-5801 and 227-5802
MODELS INVOLVED - Certain 3500B, 3500C, 3406C, C-18, C32, C27, C15, C18, C9 Generators
Dear Caterpillar Product Owner:
New software needs to be installed on the products listed below. The EMCP3 controls may reset which will cause it to change from a RUN or AUTO state to the STOP state.
You will not be charged for the service performed.Contact your local Caterpillar dealer to schedule this service. The dealer will advise you of the time required to complete this service.
Please refer to your dealer the Service Letter dated (---- This date will be filled out when the letter is issued) when scheduling this service.
We regret the inconvenience this may cause you, but urge you to have this service performed as soon as possible.
Caterpillar Inc.
Please refer the dealer to their Service Letter dated 02Mar2007 when scheduling this service.
We regret the inconvenience this may cause you, but urge you to have this service performed as soon as possible to prevent unscheduled downtime.
Caterpillar Inc.
Identification #(s)
Attached to 02Mar2007 Service Letter


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.