AVSPARE.COM
parts catalog

TUBE AS 3967733 - Caterpillar



3967733 TUBE AS Caterpillar parts 314E CR TUBE
Rating:
15
Alternative (cross code) number:
CA3967733
396-7733
3967733
Caterpillar 3967733 TUBE AS
Weight: 4 pounds 2 kg.

Buy TUBE AS 3967733 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 3967733:

EXCAVATOR  314E CR   Caterpillar
Number on catalog scheme: 7
 
  For full view, you need register

Information:

Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Bolt
1/2 inch - 20 UNF by 4 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01528461
Typical example
Always wear protective gloves when handling parts that have been heated.
If the flywheel ring gear was removed, follow Step 1.a through Step 1.c to install ring gear (3) to flywheel (1).
Identify the orientation of teeth (4) on new ring gear (3).Note: The chamfered side of the ring gear teeth must face toward the starting motor when the flywheel is installed. The correct orientation of the chamfered will ensure the correct engagement of the starting motor.
Heat flywheel ring gear (3) in an oven to a maximum temperature of 250 °C (482 °F) prior to installation.Note: Do not use a torch to heat the ring gear.
Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear onto flywheel (1).
Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" for the correct procedure.
Illustration 2 g01528438
Install a suitable lifting device on flywheel (1). The flywheel can weigh 70 kg (154 lb).
Install Tooling (A) in Position (X) on the crankshaft.
Use the lifting device to position flywheel (1) onto Tooling (A).
Install bolts (2) to flywheel (1).
Remove Tooling (A) and install remaining bolts (2) to flywheel (1).
Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) to a torque of 140 N m (103 lb ft).
Remove the lifting device from flywheel (1).
Check the run out of the flywheel. Refer to Specifications, "Flywheel" for further information.End By:
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
If necessary, install the air starting motor. Refer to Disassembly and Assembly, "Air Starting Motor - Install" for the correct procedure.
Install the generator. Refer to Disassembly and Assembly, "Generator - Install" for the correct procedure.

Caterpillar parts catalog:

Caterpillar parts catalog
315F L Excavator TDY00001-UP (MACHINE) POWERED BY C4.4 Engine
314F Excavator RAF00001-UP (MACHINE) POWERED BY C4.4 Engine
314E CR/SR & 314E LCR Excavators ECN00001-UP (MACHINE) POWERED BY C4.4 Engine


Parts tube Caterpillar catalog:

3839422 TUBE AS
314E CR, 314E LCR
3739974 TUBE AS
314E CR, 314E LCR
2895492 TUBE AS
314E CR, 314E LCR
2895491 TUBE AS
314E CR, 314E LCR
4204519 TUBE AS
314E CR, 314E LCR
4201187 TUBE AS
314E CR, 314E LCR
4201176 TUBE AS
314E CR, 314E LCR
3853016 TUBE AS
314E CR, 314E LCR
4190393 TUBE AS
314E CR, 314E LCR
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.