parts catalog

TUBE AS 5087817 - Caterpillar

5087817 TUBE AS Caterpillar parts TUBE
Alternative (cross code) number:
Caterpillar 5087817 TUBE AS
Weight: 0.41 pounds 0 kg.

Buy TUBE AS 5087817 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 6
  For full view, you need register


Diesel engine exhaust contains products of combustion which may cause personal injury.Always start and operate the engine in a well ventilated area, and, if in an enclosed area, vent the exhaust to the outside.
For maximum service life of the machine, always make a walk-around inspection of the machine. The walk around inspection must be done before you mount the machine in order to start the engine.Look around the machine and under the machine for items such as loose bolts, trash, oil leaks, coolant leaks, broken parts, or worn parts.Inspect the condition of the attachments. Inspect the condition of the hydraulic components.
Accumulated grease and oil on a machine is a fire hazard. Remove this debris with steam cleaning or high pressure water, at least every 1000 hours or each time any significant quantity of oil is spilled on the machine.
Wipe all fittings, all caps, and all plugs, before you service the machine.Note: Keep a close watch for leaks. If any leaks are observed, find the source of the leak. Repair the leak. Check the fluid levels more frequently than the recommended interval if you suspect a leak.
Illustration 1 g03342683
The engine air inlet is on the left side of the machine.
Inspect the engine air inlet for any debris or obstructions. Clean the engine air inlet if debris or an obstruction has accumulated. Note: The air filter restriction indicator is located within the monitoring system. The monitor will display a warning message and icon when the air filter requires service.
Illustration 2 g01350497
Inspect the conveyors for wear. Inspect the conveyors for damage. The conveyors may show the following signs of wear or damage: loose drag bars or broken drag bars, jerky movement of the conveyor and excessive wear on drive sprockets. Repair the conveyors if the conveyors are worn or damaged.
Illustration 3 g00861022
Inspect the auger conveyor segments for damaged components or worn components. The corners of the auger segments should be square. As the augers wear with use, the thickness and diameter may become smaller. When the edge of the auger wears to a point, the auger must be replaced.
Check the machine for loose wiring. Check the machine for frayed wiring.
Inspect the lights for broken bulbs. Inspect the lights for broken lenses. Replace the bulbs or the lenses if the bulbs or the lenses are broken.
Illustration 4 g03342688
Inspect the hydraulic system for leaks. Repair any damage before you operate the machine. Repair any leaks before you operate the machine.
All covers and guards must be securely in place. Inspect all covers and guards for damage. Repair any damage.
Inspect the steps, the walkways, and the handholds for damage or wear. Repair the components that are damaged or worn. Inspect the steps, the walkways, and the handholds for cleanliness. Clean the components.
Inspect the operator platforms for cleanliness. Keep the operator platforms clean.

Caterpillar parts catalog:

Caterpillar parts catalog
426F2 Backhoe Loader Side Shift EJ400001-UP (MACHINE) POWERED BY C4.4 Engine
426F2 Backhoe Loader Side Shift EJ200001-UP (MACHINE) POWERED BY C4.4 Engine
426F2 Backhoe Loader Side Shift DJ400001-UP (MACHINE) POWERED BY C4.4 Engine

Parts tube Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.