AVSPARE.COM
parts catalog

Tube 77050171 - Caterpillar



77050171 Tube Caterpillar parts Tube
Rating:
66
Alternative (cross code) number:
CA77050171
7705-0171
77050171
Caterpillar 77050171 Tube

Buy Tube 77050171 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 60
 
  For full view, you need register

Information:


Illustration 17 g00832298
Locate the following components:one tube (36), four clips (37), four bolts (38) and four washers (22). Leave the bolts loose. Position the tube (36) in the swing frame and fasten the tube to the blocks (3). Secure tube (36) with the following items: four clips (37), four bolts (38) and four washers (22). Leave the bolts loose.
Install hose (39) with the straight end to the hydraulic tank. Secure hose (39) with the following components:four flanges (40), two seals (41), eight bolts (21) and eight washers (22) .
Install hose (42) with the straight end to the tube. Secure hose (42) with the following components:one seal (41), two flanges (40), four bolts (21) and four washers (22) .
Secure hose (18) with the following components:one seal (2), two flanges (20), four bolts (21) and four washers (22). Install the hose to the margin relief valve (C) .
Tighten the bolts that were left loose in Step 37.
Reinstall the floor grates to the swing frame. Install any other hardware that was removed during these procedures.
Refill the hydraulic tank. Refer to the Operation and Maintenance Manual, "Refill Capacities" for the appropriate oil and the correct amount of oil.Fabricated Parts
Fabricate the following parts.
Table 12
Fabricated Parts    
Item     Qty     Part Number     Description    
3     2     190-1263     Block    
4     1     207-8551     Block    
10     2     202-6585     Block    Fabrication of 190-1263 Block
Fabricate 190-1263 Block from mild steel.
Illustration 18 g00812477
Table 13
Fabrication Dimensions for the 190-1263 Block    
Item     Dimension    
A     Two holes (10.5 mm diameter X 55 mm deep, Counterbore 15 .13 mm diameter X 25 mm deep, Chamfer 12 .5 mm diameter X 90°, Tap M12 X 1.75 -6G 25 mm deep)    
B    
17.5 0.8 mm (0.6890 0.013 inch)    
C    
35 mm (1.38 inch)(tolerance of the stock)    
D    
14.6 1.5 mm (0.58 0.06 inch)    
E    
50.8 0.8 mm (2.00 0.03 inch)    
F    
80 1.5 mm (3.15 0.06 inch)    
G    
62.5 3.6 mm (2.46 0.14 inch)    Fabrication of 207-8551 Block
Fabricate 207-8551 Block from mild steel.
Illustration 19 g00832485
Table 14
Fabrication Dimensions for the 207-8551 Block    
Item     Dimension    
A    
114 mm (4.5 inch)    
B    
110 mm (4.3 inch) wide, hot finished steel    
C    
76 mm (3 inch)    
D    
25 mm (1 inch)    
E    
50 mm (2 inch)    
F    
135 2 mm (5.3 0.08 inch)    
G     Two holes (10.5 mm diameter X 40 mm deep, Tap M12 X 1.75 -6H 30 mm deep)    Fabrication of 202-6585 Block
Fabricate 202-6585 Block from high strength structural steel with a minimum yield of 207 MPa (30000 psi).
Illustration 20 g00812479
Table 15
Fabrication Dimensions for the 202-6585 Block    
Item     Dimension    
A  

Caterpillar parts catalog:

Caterpillar parts catalog
CP-323 VIBRATORY COMPACTOR 6JD00001-00065 (MACHINE) POWERED BY 4219D ENGINE


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.