AVSPARE.COM
parts catalog

TUBE AS 9V9900 - Caterpillar



9V9900 TUBE AS Caterpillar parts 926, 926A, IT28 TUBE
Rating:
20
Alternative (cross code) number:
CA9V9900
9V-9900
9V9900
Caterpillar 9V9900 TUBE AS
Weight: 3 pounds 1 kg.

Buy TUBE AS 9V9900 Caterpillar genuine, new aftermarket tractor parts with delivery
INTEGRATED TOOLCARRIER, WHEEL LOADER,

Compatible equipment models: 9V9900:

INTEGRATED TOOLCARRIER  IT28  
WHEEL LOADER  926   926A   Caterpillar
Number on catalog scheme: 13
 
  For full view, you need register

Information:

Start By:a. separate tractor and trailer
Typical Example
D300D Hitch Pins And Fasteners1. Remove bolts (2) and nuts (3).2. Remove hitch pin washerer (6) and studs (1).3. Remove bolts (4). Set bracket assembly (5) aside if so equipped.
Typical Example4. Remove bolt, washer and taper pin (9) from each steer cylinder pin (7) at oscillating hitch (8). Remove pin (7). Repeat on other side.
Typical Example5. Secure tool (A) and tool (C) to oscillating hitch (8) and attach a hoist and chains. The oscillating hitch weighs 495 kg (1100 lb).
Typical Example6. Remove bolts (10). Remove lower hitch pin (11) by using tool (B).
Typical Example7. Use tool (B) to partially remove upper hitch pin (12). After partial removal, back off tool (B) and place two steel blocks approximately (1 inch X 2 inch) under the upper hitch pin and finish removal of the hitch pin.8. After the oscillating hitch is partially removed from the truck chassis, remove spacer or washers (13).
Typical Example9. Two face seals (14) must be removed to prevent damage to the steer cylinder rod ends as the oscillating hitch is being removed.
Typical Example10. A seal ring (15) rests between the tractor frame and the lower pin mount of the oscillating truck hitch. Raise oscillating truck hitch (8) to provide seal clearance before attempting removal. Set oscillating truck hitch on a solid base.
Typical Example11. Inspect and if necessary remove screws (17), replace two hitch thrust washers (16) from the top and bottom of the oscillating hitch flange.
Typical Example12. Inspect upper spherical bearing (18). Replace if necessary. 13. Inspect lower spherical bearing (19). Replace if necessary.Install Oscillating Truck Hitch
Typical Example1. Use two wood blocks (D) to block the steer cylinders. This will allow easier installation of the oscillating hitch.
Typical2. Secure tool (B) and tool (C) to the oscillating hitch. Attach tool (A) with chains and hoist to tools (B) and (C). Use tool (A) to obtain proper alignment.3. To complete the installation of the oscillating hitch, reverse the procedures in the removal steps in this order: Step 8, 7, 2, 1, 6, 5, 9, 4, and 3. Read before beginning installation assembly steps.
Damage to the lower seal ring could occur if care is not taken to install properly. When installing seal ring (15), refer to Photo C43738P2, provide all clearance available to place the seal ring between the tractor frame and the lower pin mount of the oscillating truck hitch. Insert the lower pin. Move to the upper pin assembly. Insert the lower spacer of the upper pin assembly. Lower truck hitch to allow insertion of upper spacer. Insert the upper pin.
End By:a. connect tractor and trailer

Caterpillar parts catalog:

Caterpillar parts catalog
IT28 INTEGRATED TOOLCARRIER 2KC00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT28B INTEGRATED TOOLCARRIER 1HF00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT28 INTEGRATED TOOLCARRIER 8JB00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT28B INTEGRATED TOOLCARRIER 5SD00001-UP (MACHINE) POWERED BY 3204 ENGINE
926 WHEEL LOADER 94Z00001-02208 (MACHINE) POWERED BY 3204 ENGINE
G926 WHEEL LOADER 1SD00001-00073 (MACHINE) POWERED BY 3204 ENGINE
926 WHEEL LOADER 4NB00001-02075 (MACHINE) POWERED BY 3204 ENGINE
926 WHEEL LOADER 8NB00001-01541 (MACHINE) POWERED BY 3204 ENGINE


Parts tube Caterpillar catalog:

8V7586 TUBE AS
926, 926A, IT28, IT28B
9V9903 TUBE AS
926, 926A, IT28
2W8981 TUBE AS.
916, 926, IT28
4W2144 TUBE AS.
916, 926, IT28
8V7621 TUBE AS
926, 926A, IT28, IT28B
8V7962 TUBE AS
926, 926A, IT28
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.