AVSPARE.COM
parts catalog

UNION HIGH 1C4296 - Caterpillar



1C4296 UNION HIGH Caterpillar parts UNION
Rating:
51
Alternative (cross code) number:
CA1C4296
1C-4296
1C4296
Caterpillar 1C4296 UNION HIGH
Weight: 1 pounds 0 kg.

Buy UNION HIGH 1C4296 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Put identification on all lines, hoses, wires and tubes for installation purposes. Cap and plug all lines, hoses and tubes to prevent foreign material from entering the system.1. Drain all fluids in a suitable container for storage or disposal.2. Drain the hydraulic system.3. Drain the power train oil system. 4. Disconnect four hose assemblies (2) from implement pump (1). 5. Disconnect four hose assemblies (3) from power train pump (4).6. Remove clip (5) from power train pump (4). 7. Disconnect hose assembly (6) from hard bar pin (7). 8. Remove hydraulic hose assembly (8).9. Remove hose assemblies (9), (10) and (11). 10. Disconnect wire harness connectors (12).11. Remove the bolt and harness clip (13). 12. Remove pin (16) and disconnect the linkage.13. Remove bolts (14) and bracket (15).14. Remove tube assemblies (17). 15. Disconnect linkage (20).16. Remove bolts (18) and linkage assembly (19). 17. Remove bolts (22) and remove guard assemblies (21) from each side of the machine. 18. Disconnect cables (23) from the starter motor.19. Remove heater hose assemblies (24).20. Remove air conditioning hose assemblies (25) from the compressor.21. Remove ground cable (26) from the frame. 22. Shut the fuel supply off at the fuel tank and remove fuel hose assemblies (27) from the engine.23. Remove air conditioning hose assembly (28) from the accumulator.24. Remove bolt and clip (29) from each side of the flywheel housing and reposition the hose assemblies away from the engine to prevent damage from pinching. 25. Install Tool (A) as shown to the lifting brackets located on the engine.26. Apply slight lifting force to the engine. 27. Remove front engine mount bolts (30) and mounts (31).28. Remove rear engine mount bolts (33) and mounts (34).29. Remove bolts (32) and remove both mount assemblies (35) from the flywheel housing. 30. Remove the engine and torque converter from the machine. The weight of the engine and torque converter is 1180 kg (2600 lb). The following steps are for the installation of the engine and torque converter. 31. Install Tool (A) as shown to the lifting brackets located on the engine.32. Place the engine and torque converter in position as shown. The weight of the engine and torque converter is 1136 kg (2550 lb). 33. Install rear mount assemblies (35) and bolts (32) on each side of the machine.34. Install rear mounts (34) and bolts (33).35. Install front mounts (31) and bolts (30). 36. Remove Tool (A). 37. Install fuel hose assemblies (27), air conditioning hose assembly (28) and clips (29). 38. Install ground cable (26).39. Install air conditioning hose assemblies (25).40. Install cables (23) to the starter motor.41. Install heater hose assemblies (24). 42. Install guard assemblies (21) and bolts (22) on each side of the machine. 43. Install bolts (18) and linkage assembly (19).44. Connect linkage (20). 45. Install tube assemblies (17).46. Install bolts (14) and bracket (15).47. Connect linkage (16). 48. Install harness clip (13).49. Connect wire harness connectors (12). 50. Install hose assemblies (9), (10) and (11).51. Install hose assembly


Parts union Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.