AVSPARE.COM
parts catalog

VALVE GP-CONTROL 5087831 - Caterpillar



5087831 VALVE GP-CONTROL Caterpillar parts VALVE
Rating:
76
Alternative (cross code) number:
CA5087831
508-7831
5087831
Caterpillar 5087831 VALVE GP-CONTROL
Weight: 18 pounds 8 kg.

Buy VALVE GP-CONTROL 5087831 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 3
 
  For full view, you need register

Information:

Removal Procedure
Start By:
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove" for the correct procedure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the front housing is not installed, do not turn the crankshaft. Damage to the engine may occur.
Illustration 1 g03331719
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Remove C-clip (9) that retains idler gear (3) onto idler hub (1).
Remove the following components from idler hub (1) collar (8), spring (7), shim (6) and oil pump cover (5).
Remove idler gear (3) from idler hub (1).
Remove inner rotor (4) from idler hub (1).
Remove thrust washer (2) from idler hub (1).
Illustration 2 g03331717
If necessary, follow Step 6.a through Step 6.d In order to remove oil strainer (13) and suction pipe (11).
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install" for the correct procedure.
Remove bolts (12) and oil strainer (13) from the cylinder block.
Remove suction pipe (11) from the cylinder block.
Remove O-ring seal (10) from the suction pipe.
Illustration 3 g03331715
Illustration 4 g03331716
If necessary, follow Step 7.a through Step 7.d In order to remove idler hub (1) from the cylinder block.
Remove camshaft (16). Refer to Disassembly and Assembly, "Camshaft - Remove" for the correct procedure.
Remove bolts (17) and plate (14) from the cylinder block.
Remove gasket (15) (not shown).
Remove crankshaft (18). Refer to Disassembly and Assembly, "Crankshaft - Remove" for the correct procedure.
Use a hammer and use a suitable drift in order to remove idler hub (1) from the cylinder block. Align the drift to the rear face of the idler hub and drive the idler hub from the inside of the cylinder block outward.

Caterpillar parts catalog:

Caterpillar parts catalog
TL1055D Telehandler ML500001-UP (MACHINE) POWERED BY C4.4 Engine
TL642D Telehandler ML800001-UP (MACHINE) POWERED BY C4.4 & C3.4 B Engine


Parts valve Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.