AVSPARE.COM
parts catalog

WEAR PAD 1246544 - Caterpillar



1246544 WEAR PAD Caterpillar parts TH103 WEAR
Rating:
52
Alternative (cross code) number:
CA1246544
124-6544
1246544
Caterpillar 1246544 WEAR PAD
Weight: 1 pounds 0 kg.

Buy WEAR PAD 1246544 Caterpillar genuine, new aftermarket tractor parts with delivery
TELEHANDLER,

Compatible equipment models: 1246544:

TELEHANDLER  TH103   Caterpillar
Number on catalog scheme: 11
 
  For full view, you need register

Information:


Push down on the power mode control button in order to activate power mode.Note: The indicator light will be illuminated when power mode is activated.
Illustration 8 g02453444
Transmission control button located on the soft panel switch
Push down on transmission control button in order to select FIRST GEAR. Note: The first indicator light will illuminate when the transmission is in FIRST GEAR.
Illustration 9 g02447036
Automatic Engine Speed Control (AESC) as displayed on the programmable function key in the monitor.
Disable the automatic engine speed control through the monitor by pressing the programmable button.
Illustration 10 g02447064
Joystick (front switch)
Disable the hydraulic modulation control, if equipped. Press the front switch on the right joystick in order to deactivate hydraulic modulation.
The air conditioning should be turned off for the following test.Test Procedure
To prevent injury or death, never work under a machine while a test is being performed.
Start Electronic Technician.
Select the "Machine ECM" from the list of available controls.
From the top menu, select "Diagnostics".
From the pull-down menu, select "Diagnostic Tests".
Then select "Override Parameters".
Illustration 11 g02413123
ET Screen (2) "Transmission output speed" (3) "Travel motor swashplate angle limit solenoid current override"
From the menu, select "Travel motor swashplate angle limit solenoid current override" and adjust the current to 0.0 amp.
Release the service brake pedal.
Depress the travel speed pedal fully in the FORWARD position.
Increase the current value at the "Travel Motor Swash Plate Angle Limit Solenoid Current Override" (3) to 0.11 amp.
Monitor the "Transmission Output Speed" (2), and slowly increase the current value to the "Travel Motor Swash Plate Angle Limit Solenoid Current Override" (2) by increments of 0.01 amp until the transmission output speed increases.
Check the pressure gauge at "M8" port (1) in order to verify that the pressure has increased to the proper specification when the transmission speed increases.Note: Refer to Table 2 in this manual for the correct pressure.
If the destroke pressure is not set to the proper specification, perform the "Adjustment Procedure" in order to adjust the destroke pressure.Adjustment Procedure
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.
Illustration 12 g02662256
Travel Motor ( M313D) (4) Adjustment screw
Illustration 13 g02413126
Travel Motor ( M315D) (4) Adjustment screw
Stop the engine.
Loosen the locknut on adjustment screw (4) for destroke pressure.
Turn adjustment screw (4) clockwise in order to decrease the destroke point. Turn adjustment screw (4) counterclockwise in order to increase the destroke point.Note: A 1/4 turn of the adjustment screw will equal approximately 200 kPa (29 psi).Note: Always make the final pressure adjustments on the pressure rise.
Tighten the locknut on adjustment screw (4) for destroke pressure.
Verify that the destroke pressure is within specifications.
Repeat Step 12 of the "Machine Preparation" procedure through Step 5 of the "Adjust Procedure", as needed.Worksheet
Table 2
"Travel Motor (Destroke Point) - Test and Adjust"    
Date:     Machine Serial Number:    
Machine Settings     Engine Speed    
Speed dial "1"
AESC switch OFF
Item     Specification  

Caterpillar parts catalog:

Caterpillar parts catalog
TH103 Telehandler 3PN00001-02026 (MACHINE) POWERED BY 3054 Engine


Parts wear Caterpillar catalog:

3312489 WEAR PAD
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.