AVSPARE.COM
parts catalog

WHEEL 1246697 - Caterpillar



1246697 WHEEL Caterpillar parts TH103 WHEEL
Rating:
65
Alternative (cross code) number:
CA1246697
124-6697
1246697
Caterpillar 1246697 WHEEL
Weight: 109 pounds 49 kg.

Buy WHEEL 1246697 Caterpillar genuine, new aftermarket tractor parts with delivery
TELEHANDLER,

Compatible equipment models: 1246697:

TELEHANDLER  TH103   Caterpillar
  For full view, you need register

Information:

Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
B     1U-9200     Lever Puller Hoist     1    
D     8T-5071     Seal Guard     1    
E     214-9540     Seal Installer     1    
F     6V-6640     Sealant     1    
Illustration 1 g01241953
If necessary, install bearing (7), retaining ring (8), seal (9), and retaining ring (10). Use Tooling (E) in order to install seal (9) .Note: Clean all mating surfaces. Wipe the surfaces in order to remove debris and contaminants.
Apply Tooling (F) onto both mating surfaces of seal (9) during assembly.Note: Lubricate the sealing surface lightly with lubricant.
Illustration 2 g01352905
Front track roller frame (6) must be supported to make level before removed from the rear track roller frame. To avoid damaging the roller frames, Tooling (B) should be used with a suitable lifting device in order to support the front track roller frame until the guide slots are no longer visible.
Attach a suitable lifting device and Tooling (B) to the rear of front track roller frame (6). Attach two suitable chains to front track roller frame (6) and attach to Tooling (B). Use Tooling (B) to help keep front track roller frame (6) level. The weight of front track roller frame (6) is approximately 1565 kg (3450 lb). Use Tooling (D) in order to protect the seals in rear track roller frame (4). Install front track roller frame (6) until the suitable lifting device contacts rear track roller frame (4). Remove the suitable lifting device.
Illustration 3 g01352638
Position a suitable chain around track idler (11). Attach Tooling (B) to the suitable chain. Attach another suitable lifting device to the other end of Tooling (B) and to the hook on rear track roller frame (4). Remove Tooling (D). Use Tooling (B) in order to install front track roller frame (6) into rear track roller frame (4) .
Illustration 4 g01242479
Install guide assembly (5) to both sides of rear track roller frame (4) .
Illustration 5 g01241945
Position O-ring seal (3) (not shown) and position cover (2). Install bolts (1) and the washers. Repeat for the opposite side.
Fill the recoil spring compartment with oil. Refer to Operation and Maintenance Manual, "Recoil Spring Compartment Oil Level - Check".
Repeat Steps 1 through 7 for the opposite side of the machine.End By: Connect the track.

Caterpillar parts catalog:

Caterpillar parts catalog
TH103 Telehandler 3PN00001-02026 (MACHINE) POWERED BY 3054 Engine
TH103 Telehandler 3PN02027-UP (MACHINE) POWERED BY 3054 Engine


Parts wheel Caterpillar catalog:

1197789 WHEEL AS
416C, 420D, 426C, 428B, 430D, 436C, 438C
1197785 WHEEL AS
416C, 416D, 420D, 424D, 426C, 428B, 428C, 428D, 432D, 436C, 438B, 438C, 438D, 442D
1R1184 WHEEL AS-DRIVE-RH
65C, 65E, 75D, 75E, 85D, 85E, 95E
1R1185 WHEEL AS-DRIVE-LH
65C, 65E, 75D, 75E, 85D, 85E, 95E
2713050 WHEEL AS
416D, 420D, 424D, 428C, 428D, 432D, 438D, 442D
2713042 WHEEL AS
416C, 416D, 420D, 424D, 428C, 428D, 430D, 432D, 438C, 438D, 442D
1021380 WHEEL AS
416C, 416D, 420D, 428C, 428D, 438B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.