AVSPARE.COM
parts catalog

WIPER GP-WINDOW 2333139 - Caterpillar



2333139 WIPER GP-WINDOW Caterpillar parts 120M, 120M 2, 12M, 140M, 140M 2, 14M, 160M, 160M 2, 16M WIPER
Rating:
32
Alternative (cross code) number:
CA2333139
233-3139
2333139
Caterpillar 2333139 WIPER GP-WINDOW

Buy WIPER GP-WINDOW 2333139 Caterpillar genuine, new aftermarket tractor parts with delivery
MOTOR GRADER,

Compatible equipment models: 2333139:

MOTOR GRADER  120M   120M 2   12M   140M   140M 2   14M   160M   160M 2   16M   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

Transmission ECM
The following is a list of Diagnostic Trouble Codes (DTCs) that are associated with the electrical power supply circuits of the machine.
Table 2
Transmission ECM (MID 81)
DTC Code Description System Response
168-2 Electrical System Voltage: Data Erratic, Intermittent, or Incorrect All new sensor diagnostic codes are disabled after this event goes active. Any old sensor diagnostic codes will remain active until this event is cleared.
168-3 Electrical System Voltage: Voltage Above Normal The ECM activates this diagnostic code when the system voltage is above 32.0 VDC.
168-4 Electrical System Voltage: Voltage Below Normal The ECM activates this diagnostic code when the system voltage is below 20.0 VDC. Note: Prior to beginning this procedure, inspect the harness connectors that are involved in this circuit. Poor connections may be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. If a problem with a connection is found, correct the problem and verify that the diagnostic code is active before performing a troubleshooting procedure.Possible causes for an FMI 2 Diagnostic code are:
A charging system component has failed.
Intermittent connection in the battery circuit for the ECM.
The ECM has failed. A failure of the ECM is unlikely.Possible causes for an FMI 3 Diagnostic code are:
The sensor supply or the ground circuit in the machine harness is open.
The signal circuit in the machine harness is shorted to another circuit.
The signal circuit in the machine harness is open or the sensor is disconnected.
The sensor has failed.
The ECM has failed. A failure of the ECM is unlikely.Possible causes for an FMI 4 Diagnostic code are:
The signal circuit in the machine harness is shorted to ground.
The sensor has failed.
The ECM has failed. A failure of the ECM is unlikely.
Illustration 2 g03592700
Schematic of the Power Supply circuits
Note: The diagram above is a simplified schematic of the connections for the Power Supply circuits. The schematic is electrically correct. However, not all of the possible harness connectors are shown. Refer to the latest revision of the Electrical Schematic, UENR3102 for the complete schematic.Diagnostic Trouble Code Procedure
Note: Prior to beginning this procedure, inspect the harness connectors that are involved in this circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. Check the wiring for pinch points or abrasions. Look for and repair areas that indicate wires are exposed. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing a troubleshooting procedure.
Table 3
Troubleshooting Test Steps Values Results
1. Identify Active FMI Code Associated With The System Voltage Circuit
Code present. FMI 2 diagnostic code, proceed to Test Step 2.
FMI 3 diagnostic code, proceed to Test Step 3.
FMI 4 diagnostic code, proceed to Test Step 6.
Begin Process For FMI 2 Troubleshooting HERE
2. Test The Battery
A. Turn Key start switch to the ON position.
B. Observe the status of the diagnostic code.
The diagnostic code is NOT active.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
16M Motor Grader B9H00001-UP (MACHINE) POWERED BY C13 Engine
14M Motor Grader B9J00001-UP (MACHINE) POWERED BY C11 Engine
160M Motor Grader B9L00001-UP (MACHINE) POWERED BY C9 Engine
120M Motor Grader B9N00001-UP (MACHINE) POWERED BY C6.6 Engine
140M Motor Grader B9M00001-UP (MACHINE)
160M Motor Grader B9E00001-UP (MACHINE) POWERED BY C9 Engine
12M Motor Grader B9R00001-UP (MACHINE) POWERED BY C6.6 Engine
140M Motor Grader B9D00001-UP (MACHINE)
12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine
120M Motor Grader B9C00001-UP (MACHINE) POWERED BY C6.6 Engine
120M Motor Grader - All Wheel Drive B9W00001-UP (MACHINE) POWERED BY C6.6 Engine
120M Motor Grader - All Wheel Drive D9W00001-UP (MACHINE) POWERED BY C6.6 Engine
140M Motor Grader - All Wheel Drive B9G00001-UP (MACHINE) POWERED BY C9 Engine
140M Motor Grader - All Wheel Drive D9G00001-UP (MACHINE) POWERED BY C9 Engine
160M Motor Grader - All Wheel Drive B9T00001-UP (MACHINE) POWERED BY C9 Engine
160M Motor Grader - All Wheel Drive D9T00001-UP (MACHINE) POWERED BY C9 Engine
120M Motor Grader R9A00001-UP (MACHINE) POWERED BY C6.6 Engine
12M Motor Grader R9B00001-UP (MACHINE) POWERED BY C6.6 Engine
120M Motor Grader - All Wheel Drive R9C00001-UP (MACHINE) POWERED BY C6.6 Engine
14M Motor Grader R9J00001-UP (MACHINE) POWERED BY C11 Engine
16M Motor Grader R9H00001-UP (MACHINE) POWERED BY C13 Engine


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.