AVSPARE.COM
parts catalog

WIRING GP-LIGHTING 2333125 - Caterpillar



2333125 WIRING GP-LIGHTING Caterpillar parts 14M, 160M WIRING
Rating:
85
Alternative (cross code) number:
CA2333125
233-3125
2333125
Caterpillar 2333125 WIRING GP-LIGHTING

Buy WIRING GP-LIGHTING 2333125 Caterpillar genuine, new aftermarket tractor parts with delivery
MOTOR GRADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
REEL - HOSE LEFT HAND FOR CLARK: 2333125
$560.27
 

01 Mar 2021

-: -
REEL - HOSE LEFT HAND FOR CLARK: 2333125
CLARK || All Brand new & rebuilt items comes with 1 year warranty. || REEL - HOSE LEFT HAND. Category: CLARK FORKLIFT PARTS. This part can also be found under the following part numbers: CL2333125 2333125  CLARK 2333125  CLARK2333125 2333125     . All Brand new & rebuilt items comes with 1 year warranty.
2333125 Hose Reel (Left Hand) for Clark
$809.06
 

01 Mar 2021

-: -
2333125 Hose Reel (Left Hand) for Clark
Hydraulics || Hydraulic Hose Reels || Home > Hydraulics > Hydraulic Hose Reels
Number on catalog scheme:
 
  For full view, you need register

Compatible equipment models: 2333125:

MOTOR GRADER  14M   160M   Caterpillar

Information:

Specification
Table 1
"Travel on Level Ground - Test (Optional Test)"
Time For Three Revolutions (time in seconds)
Undercarriage Travel Speed New Service Limit Actual
Right Left
Long HIGH Forward 17.2 1.0 22.3 or less
Reverse
LOW Forward 28.4 1.0 36.9 or less
Reverse Introduction
When the procedure for the Travel on Level Ground cannot be performed, this test may be used as a substitute.Note: The engine speed and/or the machine configuration that is used during this test can affect the results of this test. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for the engine speed that was used for this test. Refer to Testing and Adjusting, "Operational Checks" for the machine configurations that were used for this test.Note: The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check. Refer to Testing and Adjusting, "Specifications".Required Tools
Table 2
Description Qty
Stopwatch 1 Test Procedure
Start the engine.
Position the machine on level ground.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Illustration 1 g00297292
Raise a track off the ground. Refer to Illustration 1.
Put a mark on a shoe of the raised track.
Place the machine controls at the following settings: Engine speed dial "10" and AEC switch OFF.
Place the travel speed control switch in HIGH position.
Move the travel lever of the raised track to full travel position.
Measure the time that is required for the raised track to make three complete revolutions. Measure the time that is required in each direction. Note: The difference in times between forward and reverse should not exceed 0.5 seconds for HIGH travel speed and 1.0 seconds for LOW travel speed.
Place the travel speed control switch in the LOW position and repeat Steps 8 through 9.

Caterpillar SIS machinery equipment:

Caterpillar SIS


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.