AVSPARE.COM
parts catalog

WIRING GP-FRONT 3967831 - Caterpillar



3967831 WIRING GP-FRONT Caterpillar parts 901C, 902C, 903C WIRING
Rating:
44
Alternative (cross code) number:
CA3967831
396-7831
3967831
Caterpillar 3967831 WIRING GP-FRONT

Buy WIRING GP-FRONT 3967831 Caterpillar genuine, new aftermarket tractor parts with delivery
COMPACT WHEEL LOADER,

Compatible equipment models: 3967831:

COMPACT WHEEL LOADER  901C   902C   903C   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 1 g06253158
Typical example
Table 1
Item Qty Part Specification Description
1 - - Tighten the unit injector rocker arm locknut to 100 10 N m (74 7 lb ft).
2 - - Tighten the valve rocker arm locknut to 30 7 N m (266 62 lb in).
3 1 313-4085 Rocker Shaft Assembly Diameter of a new rocker shaft is 40.000 0.010 mm (1.5748 0.0004 inch).
After installation, bore in the rocker arm bushing for rocker shaft is 40.065 0.015 mm (1.5774 0.0006 inch).
Bore in the valve rocker arm for rocker shaft is 40.065 0.015 mm (1.5774 0.0006 inch).
- - - Inlet valve lash setting is 0.38 0.08 mm (0.015 0.003 inch).
Exhaust valve lash setting is 0.76 0.08 mm (0.030 0.003 inch).
Illustration 2 g06253165
Typical example
Left side view of engine
Illustration 3 g03141256
Typical example
Tightening sequence
Table 2
Item Qty Part Specification Description
4 24 356-5212 Bolt Use the following procedure to tighten the bolts for the rocker arm:
Before assembly, lubricate the threads and shaft to bolt interface with clean engine oil.
1. Tighten the bolts in 2, 3, 1, 4 sequence to 55 5 N m (41 4 lb ft).
2. Retighten the bolts in 2, 3, 1, 4 sequence to 55 5 N m (41 4 lb ft).
3. Again, tighten the bolts in 2, 3, 1, 4 sequence to an additional angle of 60 5 degrees.
Illustration 4 g06248453
437-3877 Rocker Arm
Table 3
Item Qty Part Specification Description
5 1 276-5317 Nut Hold the Arm adjustment screw in position and tighten the nut to 6 3 N.m (53 27 lb in).
6 1 274-4491 Arm Adjustment Screw Free running torque of Arm adjustment screw must not exceed 0.4 N.m (3.5 lb in).
Illustration 5 g06248456
Typical example
489-8223 Rocker Arm
Table 4
Item Qty Part Specification Description
7 1 274-4492 Arm Adjustment Screw Free running torque of Arm adjustment screw must not exceed 0.4 N.m (3.5 lb in).
8 1 196-5070 Jam Nut Hold the Arm adjustment screw in position and tighten the nut to 6 3 N.m (53 27 lb in).

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
901C Compact Wheel Loader W4T00001-UP (MACHINE) POWERED BY C1.8 Engine
902C Compact Wheel Loader W5T00001-UP (MACHINE) POWERED BY C2.4 Engine
903C Compact Wheel Loader W6T00001-UP (MACHINE) POWERED BY C2.4 Engine
903C Compact Wheel Loader MW400001-UP (MACHINE) POWERED BY C2.4 Engine


Parts wiring Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.