AVSPARE.COM
parts catalog

WIRING GP-CAB 4647327 - Caterpillar



4647327 WIRING GP-CAB Caterpillar parts WIRING
Rating:
76
Alternative (cross code) number:
CA4647327
464-7327
4647327
Caterpillar 4647327 WIRING GP-CAB

Buy WIRING GP-CAB 4647327 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme:
 
  For full view, you need register

Information:

Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1P-0520     Driver Gp     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00913137
Install crankshaft gear (8) and the bolts.
Illustration 2 g00913136
Install shaft (7) and the bolts. The torque for the bolts is 140 10 N m (105 5 lb ft).
Illustration 3 g01051669
Illustration 4 g01068502
(4) Camshaft Idler Gear. (9) Bearing. (E) 81.060 0.010 mm (3.1913 0.0004 inch). (F) 1.00 0.25 mm (0.040 0.010 inch).
Use Tooling (A) and a suitable press to install the bearings in camshaft idler gears (4) . Install bearing (9) into gear (4) to Depth (F) , as shown.
Machine the inside diameter of bearing (9) to Dimension (E) , as shown.Note: The surface finish of Bore (E) must be 0.8 micrometers. Pitch Diameter (H) must be concentric with a total indicator reading of 0.12 mm (0.005 inch). Surface (G) of gear (4) must be square with Bore (E) within 0.05 mm (0.002 inch).
Place clean engine oil on the bearings and install shafts (5) with washers (6) on camshaft idler gears (4) .
Illustration 5 g00913054
Install camshaft idler gears (4) and the bolts.
Illustration 6 g01068516
(2) Cluster Idler Gear. (3) Bearing. (A) 75.060 0.010 mm (2.9551 0.0004 inch). (B) 1.5 0.5 mm (0.06 0.02 inch).
Use Tooling (A) and a suitable press to install bearing (3) in gear (2) . Install bearing (3) to Depth (B) , as shown.
Machine the inside diameter of the bearing to Dimension (A) , as shown.Note: The surface finish of Bore (A) must be 0.8 micrometers. Pitch Diameter (C) must be concentric with a total indicator reading of 0.15 mm (0.006 inch). Surface (D) of gear (2) must be square with Bore (A) within 0.05 mm (0.002 inch).Note: The following Step is for 3508 and G3508 Engines.
Illustration 7 g01056631
Note: When you install the rear cluster gear assembly to the crank gear, there are no timing marks on the 3512, 3516, G3512 and G3516 engines. On the 3508 and G3508 engines, the rear cluster gears have timing marks that must be aligned with the marks that are on the cluster gears.
Put clean engine oil on the bearing and install the gear assembly on the shaft. Make sure that the marks on the gear assembly and the crankshaft are in alignment with the rotation of the engine, as shown.
Illustration 8 g00913045
Place clean engine oil on gear (2) and install gear (2) on the engine.
Install plate (1) and the bolts.End By: Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Install".

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
910K Compact Wheel Loader L2200001-UP (MACHINE) POWERED BY C4.4 Engine
914K Compact Wheel Loader L2400001-UP (MACHINE) POWERED BY C4.4 Engine
920K Compact Wheel Loader B9800001-UP (MACHINE) POWERED BY C4.4B Engine
914K Compact Wheel Loader BF400001-UP (MACHINE) POWERED BY C4.4B Engine


Parts wiring Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.