AVSPARE.COM
parts catalog

WIRING GP 9V9644 - Caterpillar



9V9644 WIRING GP Caterpillar parts 936 WIRING
Rating:
10
Alternative (cross code) number:
CA9V9644
9V-9644
9V9644
Caterpillar 9V9644 WIRING GP
Weight: 0.37 pounds 0 kg.

Buy WIRING GP 9V9644 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 9V9644:

WHEEL LOADER  936   Caterpillar
  For full view, you need register

Information:


Illustration 5 g01866794
Typical example
Table 3
Specifications for 385-4313 Tappet    
Callout     Part Number     Part Name     Specification Description    
A     385-4313     Tappet     Diameter of body...................
21.938 to 21.963 mm (0.86370 to 0.86468 inch)    
-     -     -     Bore diameter in the cylinder block ...................
22.000 to 22.032 mm (0.86614 to 0.86740 inch)    
-     -     -     Clearance...................
0.037 to 0.094 mm (0.00146 to 0.00370 inch)    Removal Procedure
Start By:
Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod" for the correct procedure.
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front)" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The engine should be mounted on a suitable stand and placed in the inverted position.
Illustration 6 g02311154
Remove thrust washer (1) from the cylinder block. Do not remove dowel (2) from the cylinder block unless the dowel is damaged.Note: The thrust washer has one Slots (X) .
Illustration 7 g02009035
Do not damage the lobes or the bearings when the camshaft is removed or installed.
Carefully remove camshaft (3) from the cylinder block.
If necessary, remove key (4) from camshaft (3) .Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Clean the camshaft and the thrust washer. Inspect the camshaft and the thrust washer for wear and for damage. Replace any components that are worn or damaged.
Clean the camshaft bearing in the cylinder block. Inspect the camshaft bearing for wear and for damage. If necessary, replace the camshaft bearing. Refer to Disassembly and Assembly, "Camshaft Bearing".
Replace all lifters when a new camshaft is installed.
Inspect the lifters for wear and for damage. Replace any lifters that are worn or damaged. Refer to Disassembly and Assembly, "Lifter Group" for the correct procedure.
Illustration 8 g02009035
If necessary, install a new key (4) into camshaft (3) .
Lubricate the bearing surfaces of camshaft (3) and lubricate the lobes of the camshaft with clean engine oil.
Do not damage the lobes or the bearings when the camshaft is removed or installed.
Carefully install camshaft (3) into the cylinder block.
Illustration 9 g02311154
Lubricate the thrust washer with clean engine oil. Align Slot (X) in thrust washer (1) with dowel (2) in the cylinder block. Install thrust washer (1) into the recess in the cylinder block.Note: The thrust washer has one Slots (X) .End By:
Install the front housing. Refer to Disassembly and Assembly, "Housing (Front)" for the correct procedure.
Install the rockershaft and pushrods. Refer to Disassembly and Assembly, "Rocker shaft and Pushrod" for the correct procedure.

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts wiring Caterpillar catalog:

2675633 WIRING GP-CONTROL
420E, 430E, 432E, 434E, 442E, 444E
1860301 WIRING GP-QUICK COUPLER
420D, 424D, 430D, 432D, 442D
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.