AVSPARE.COM
parts catalog

YOKE-END 1C3947 - Caterpillar



1C3947 YOKE-END Caterpillar parts PR-1000 YOKE
Rating:
61
Alternative (cross code) number:
CA1C3947
1C-3947
1C3947
Caterpillar 1C3947 YOKE-END
Weight: 13 pounds 6 kg.

Buy YOKE-END 1C3947 Caterpillar genuine, new aftermarket tractor parts with delivery
COLD PLANER,

Compatible equipment models: 1C3947:

COLD PLANER  PR-1000   Caterpillar
Number on catalog scheme: 47
  
  For full view, you need register

Information:


Illustration 1 g02065174
Schematic of the "Boom Cylinder Rod Pressure" SensorThis diagnostic code is recorded when the Machine ECM reads the signal voltage of the pressure sensor as being too low. The possible causes of this diagnostic code are listed below:
Wire E411-YL is shorted to ground.
The sensor has failed.
The ECM has failed. This is unlikely.Test Step 1. CHECK THE SENSOR
Turn the disconnect switch and the key start switch to the ON position.
Ensure that the diagnostic code is active.
Observe the status of the diagnostic code. Disconnect the machine harness from the sensor.Expected Result:The diagnostic code will remain active if the sensor is not the cause of the problem. The sensor is the cause of the problem if the diagnostic code is NO longer active.Results:
OK - The diagnostic code remains active. The sensor has not failed. The machine harness may have failed or the Machine ECM may have failed. Proceed to Test Step 2.
NOT OK - The diagnostic code is NO longer active.Repair: The machine harness and the Machine ECM are operating properly. The sensor has failed. Replace the sensor.STOPTest Step 2. CHECK THE SIGNAL CIRCUIT FOR A SHORT TO GROUND
The sensor remains disconnected from the machine harness.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector J1 and J2 from the Machine ECM.
At the J1 machine harness connector, measure the resistance from contact J1-37 (E411-YL) to all source of ground.Expected Result: The resistance should be greater than 5 ohms. Results:
OK - The resistance is greater than 5 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - The resistance is less than 5 ohms.Repair: There is a short in the machine harness. The short is between the signal circuit (wire E411-YL) and the circuit with the low resistance measurement. Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Clean the contacts of the harness connectors.
Reconnect all harness connectors.
Observe the status of the diagnostic code.
Operate the machine.
Observe the status of the diagnostic code.Expected Result:The diagnostic code is NO longer active.Results:
YES - The diagnostic code is NO longer active. The diagnostic code does not exist at this time. The initial diagnostic code was probably caused by a poor electrical connection and/or a short at one of the harness connectors that was disconnected and then reconnected. Resume normal machine operation.STOP
NO - The diagnostic code has not been corrected. The Machine ECM has failed. Repair: It is unlikely that the Machine ECM has failed. Exit this procedure and perform this diagnostic code procedure again. Replace the ECM if the cause of the diagnostic code is not found. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP

Caterpillar parts catalog:

Caterpillar parts catalog
PR-1000C Cold Planer 5XC00138-UP (MACHINE) POWERED BY 3208 Engine


Parts yoke Caterpillar catalog:

7X7244 YOKE-IDLER
PR-1000, PR-750B
7X7244 YOKE-IDLER
PR-1000, PR-750B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.